70MM AVANTI REALISTIC RETRACT & FLAPS INSTALLED RIGID STRONG DURABLE EPO STABLE SMOOTH FLYING PERFORMANCE FMSMODEL.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product,personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and failure to do so could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision.
Table of Contents Introductions ··························································································································3 Contents of Kit ························································································································4 Model Assembly ······················································································································5 Battery and radio installation ····················································
Wingspan: 900mm (35.4in) Overall Length: 1050mm (41.3in) Flying Weight: Around 1750g Motor Size: Brushless 2860-KV1850 or 2845-KV2750 Wing Load: 101.7 g/dm² (0.23oz/in²) Wing Area: 17.2 dm² (266.6sq.in) ESC: 70A Servo: 9g metal digital Servo x 8 Contents of Kit Before assembly, please inspect the contents of the kit. The photo below details the contents of the kit and labels.
Model Assembly Main Wing Installation 1. Slide the tube into the fuselage then install both wings over the wing tube and into the wing slot of the fuselage. (fig1) Note: The connectors on both sides should be attached precisely and firmly. 2.Secure the both wings into the fuselage using the included 4 screws. (fig2) fig1 HKM3.
Model Assembly Horizontal Stabilizer Installation: 1.Connect the elevator servo connectors to the servo extensions in the fuselage. 2.Slide the horizontal tail in the rear of the fuselage. Ensure the control horn faces down as shown. (fig3) 3.Secure the horizontal tail in place using the included screw. (fig4) fig3 HKM3.
Model Assembly Vertical Stabilizer Installation: 1.Connect the rudder servo connectors to the servo extensions in the fuselage. 2.Slide the vertical tail into the slot in the fuselage. (fig5) 3.Secure the vertical tail in place using the included 2 screws. (fig6) fig5 HKM3.
Battery and radio installation 1. Apply the loop side (soft side) of the hook and loop tape to the bottom of the battery and the hook side to the battery tray. 2. Install the fully charged battery in the battery compartment with the power supply cable toward the rear end of the plane, and secure using the hook and loop straps. Note: you may need to relocate the battery position to achieve the correct CG for your model.
Get your model ready to fly Important ESC and model information 1. The ESC included with the model has a safe start. If the motor battery is connected to the ESC and the throttle stick is not in the low throttle or off position, the motor will not start until the throttle stick is moved to the low throttle or off position. Once the throttle stick is moved to the low throttle or off position, the motor will emit a series of beeps.
Check the control throws The suggested control throw setting for FMS MODEL are as follows (dual rate setting): 17 15 30 12 10 20 Tips: On first flight, fly the model in low rate. The first time you use high rates, be sure to fly at low to medium speeds. High rate, as listed, is only for EXTREME maneuvering.
Control Horn and Servo Arm Settings The table shows the factory settings for the control horns and servo arms. Fly the aircraft at the factory settings before making changes. After flying, you may choose to adjust the linkage positions for the desired control response.
Check the C.G. (Center of Gravity) When balancing your model, adjust the motor battery as necessary so the model is level or slightly nose down. This is the correct balance point for your model. After the first flights, the CG position can be adjusted for your personal preference. 1. The recommended Center of Gravity (CG) location for your model is (100-105mm) forward from the leading edge of the main wing (as shown) with the battery pack installed. Mark the location of the CG on top of the wing. 2.
Before flying the model Find a suitable flying site Find a flying site clear of buildings, trees, power lines and other obstructions. Until you know how much area will be required and have mastered flying your plane in confined spaces, choose a site which is at least the size of two to three football fields - a flying field specifically for R/C planes is best. Never fly near people especially children, who can wander unpredictably.
Flying Course Take off While applying power, slowly steer to keep the model straight. The model should accelerate quickly. As the model gains flight speed you will want to climb at a steady and even rate. It will climb out at a nice angle of attack (AOA). Flying Always choose a wide-open space for flying your plane. It is ideal for you to fly at a sanctioned flying field. If you are not flying at an approved site always avoid flying near houses, trees, wires and buildings.
Trouble shooting 15
Spare parts list content FMSPX101RED FMSPX102RED FMSPX103RED FMSPX104RED FMSPX105RED FMSPX106 FMSPX107 FMSPX108RED FMSPX109 FMSPX110RED FMSPX111RED FMSPX112RED FMSPX113RED FMSRE012 FMSRE015 FMSCON003 FMSDF12B70 PRKV1850 PRKV2750 PRESC013 FMSSER9MGDP FMSSER9MGDR Fuselage Main Wing Set Vertical Stabilizer Horizontal Stabilizer Cockpit Linkage Rod Screw Set Main Landing Gear Door Pipe Landing Gear Set Main Landing Gear System Front Landing Gear System Decal Sheet Electronic Retract Electronic Retract Multi Co
ESC instruction Battery Pack A quality connector is essential ESC Motor Brushless Controller Receiver 17
