Instructions for use

3
3. You must take time to build straight, true and strong.
4. You must use an R/C radio system that is in fi rst-class
condition, and a correctly sized motor and components
throughout the building process.
5. You must correctly install all R/C and other components
so that the model operates correctly on the ground and in
the air.
6. You must check the operation of the model before every
fl ight to ensure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
clevises or other connectors often and replace them if they
show any signs of wear or fatigue.
7. If you are not an experienced pilot or have not fl own
this type of model before, we recommend that you get
the assistance of an experienced pilot in your R/C club for
your fi rst fl ights. If you’re not a member of a club, your local
hobby shop has information about clubs in your area whose
membership includes experienced pilots.
8. While this kit has been fl ight tested to exceed normal use,
if the plane will be used for extremely high stress fl ying, such
as racing, or if a motor larger than one in the recommended
range is used, the modeler is responsible for taking steps to
reinforce the high stress points and/or substituting hardware
more suitable for the increased stress.
We, as the kit manufacturer, provide you with a top quality,
thoroughly tested kit and instructions, but ultimately the
quality and fl yability of your fi nished model depends
on how you build it; therefore, we cannot in any way
guarantee the performance of your completed model,
and no representations are expressed or implied as to the
performance or safety of your completed model.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
ADDITIONAL ITEMS REQUIRED
Radio Control System
The Mini Switch Tx-R (transmitter ready) comes with the
servos and a Tactic
™
TR624 receiver installed, so all that is
required is a basic 4
+
channel transmitter. The Tactic TTX404
2.4GHz spread spectrum 4-channel radio control system
(TACJ2404) is included with the RTF (ready to fl y) version of
the Mini Switch, so this same radio system will work for your
Tx-R version, too.
❍ Tactic TTX404 2.4GHz 4-channel system (TACJ2404)
❍ (4) AA batteries will be required to operate the
recommended transmitter (FUGP4304).
A more versatile transmitter is the Tactic TTX650 digital
programmable transmitter. The TTX650 is loaded with features
which will be useful with the Mini Switch such as a fl ight timer,
dual rates, end-point adjustment, and exponential. Built-in
mixes and user programmable mixes will accommodate your
radio needs for future, more advanced models as well.
❍ Tactic TTX650 2.4GHz 6-channel computer Tx only
(TACJ2650)
If you already own a transmitter that you plan to use with the
Mini Switch, fi rst make sure it is in the compatibility list at www.
Tx-Ready.com/anylink-chart.html. If so, you can purchase
the AnyLink 2.4GHz Universal Radio Adapter to allow your
transmitter to communicate with the pre-installed Tactic receiver.
❍ Tactic AnyLink
™
2.4GHz Universal Radio Adapter
(TACJ2000)
❍ Tactic AnyLink SLT
™
2.4GHz Adapter Cable Futaba
®
Hitec
®
Round (TACM0003)
❍ Tactic AnyLink SLT 2.4GHz Adapter Cable Hitec
Aurora (TACM0004)
❍ Tactic AnyLink SLT 2.4GHz Cable Spektrum
®
DX4e/5e/7s/8 (TACM0005)
❍ Tactic AnyLink SLT Cable Fut 12Z/14MZ/18MZ/4YF
2.4GHz (TACM0007)
❍ Tactic AnyLink SLT Cable Spek DX4e/5e/7s/8/10t/18/
Deans (TACM0008)
❍ Tactic AnyLink SLT Power Combo Spektrum DX4e
5e 18T Hit (TACM0015)
Battery and Charger
The Mini Switch RTF comes complete with a motor battery
and charger. The Tx-R version requires a 1300 mAh 11.1V
LiPo battery and LiPo Charger. The Mini Switch was designed
for the Flyzone 1300mAh 11.1V LiPo battery (FLZA6014).
Other LiPo batteries similar in size with the same voltage
and capacity may also work, but they may not fi t properly in
the battery compartment or have the same type of battery
connector. In addition to a battery, a LiPo battery charger is also
required and there are several that will work (depending on your
budget and requirements). A safe, economical charger is the
ElectriFly
®
3S (3-cell/11.1V) LiPo Smart Charger (GPMM3318).
The Smart Charger includes adapters to charge from a 110V
wall outlet or a 12V DC outlet from a car. The Smart Charger
will take approximately 3-1/2 hours to fully charge the battery.
The Smart Charger will time out after 2 hours and 40 minutes
when charging the recommended battery. An additional hour
on the charger will bring the capacity of the battery to near full.
Some pilots prefer to have several batteries and charge them
faster so they can fl y more. For charging up to four batteries
faster at the same time, the Great Planes PolyCharge4
™
DC-
powered LiPo charger (GPMM3015) is recommended. But
unlike the Smart Charger, the PolyCharge4 does not have
an internal LiPo cell balancer which is a critical component in
making sure your LiPo batteries charge effi ciently and evenly.
So, for each LiPo battery you wish to charge simultaneously,
one Great Planes Equinox
™
LiPo Cell Balancer (GPMM3160)
will also be required. Finally, the PolyCharge4 does not have
AC capability, so if wall charging is a priority, a separate AC
12-Volt power source must also be purchased separately. A
suitable power supply for the PolyCharge4 is the Great Planes
12V 12A DC power supply (GPMP0901).