USER MANUAL VERSION 1.
Copyright 2019 All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
13. The medical PC can be cleaned in accordance with normal clinical cleaning practices, including wiping with water or medical grade wipes, provided no substance containing acids or cleaning alkali liquids is used. 14. Medical grade wipes must not contain more than 80% alcohol content measured against the total content of the wipe. 15. Operator shall not contact patient simultaneously when in use with the medical computer. Sécurité INSTRUCTIONS IMPORTANTES RELATIVES À LA SECURITE 1.
CE MARK This device complies with the requirements of the EEC directive 2014/30/EU with regard to “Electromagnetic compatibility” and 2014/35/EU “Low Voltage Directive”. FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Avertissement Batterie Risque d’explosion si la batterie est remplacée par un élément incompatible. Jetez les batteries usagées selon les instructions des dispositions locales . Avertissement de sécurité Remarque: Pour répondre à la norme IEC60950-1 alinéa 2.5 (sources d’énergie limitées, LPS) liés la législation, les périphériques doivent être conforme 4.7.3.2 “Matériaux pour enceinte coupe-feu» 4.7.3.
Troubleshooting For your own safety and that of your equipment, always take the following precautions. Disconnect the power plug (by pulling the plug, not the cord), from your computer if any of the following conditions exists: • The power cord or plug becomes frayed or otherwise damaged. • You spill something into the system. • Your computer has been dropped or damaged. • You suspect that your computer needs service or repair. • You want to clean the computer or screen.
Revision History Changes to the original user manual are listed below: Revision 1.
Table of Contents 1. Intended Use................................. 1 2. Packing List .................................. 2 2-1. Standard Items ................................................................2 2-2. Optional Items .................................................................2 3. System View.................................. 3 3-1. 3-2. 3-3. 3-4. Front & Side View ............................................................3 Rear & Bottom View ............................................
6. Specification ................................ 11 7. Configuration ............................... 13 7-1. D87U Motherboard Layout ............................................13 7-2. Connectors & Functions ................................................14 7-3. Jumper Setting ...............................................................
1. Intended Use The Medical Computer is a computing device capable of storing, retrieving and sending data electronically. This Medical Computer, including its user interface, RTC battery, PCB and power supply, is intended to be fixed to a VESA wall mount in medical care environment. This Medical Computer Hardware System must be operated by professional personnel (i.e., doctor, nurse...). Application: Access to patient records / Hospital administration system / Bed management.
2. 2-1. Packing List Standard Items a. b. c. d. a. b. c. d. System Power adapter Power cord RJ45-DB9 cable (x2) Note: Power cord will be supplied differently according to various region or country. 2-2. Optional Items a. a.
3. 3-1. System View Front & Side View 1 5 樣品有 6 7 2 Item No. 1 2 3 4 5 6 7 3 3 4 Description 2M front camera (option) 21.
有電池蓋子 3-2. Rear & Bottom View 1 2 3 4 5 Item No. 1 2 3 4 5 3-3. Description 100 x 100 VESA mounting holes 75 x 75 VESA mounting holes Battery door Cable cover LED reading light I/O view a Item No. a b c d e f g h i j k k b c d e 樣品無 f g h i j Description VGA nd 2 LAN Mic inCOM4 Line out USB 3.
3-4. Dimension 324.64mm 533.
4. 4-1. Basic Operation Powering ON & OFF To activate the system, push and quickly release the power button and the display will come on in a few seconds. NOTE: The system must be plugged into power adapter or battery charged before turning on for the first time. To turn off the system, power off the device safely using software function that “shuts down computer” provided in the operating system.
4-2. Charing the Battery The system is equipped with 3 hot-swappable batteries that support up to 12 hours per charge depending on usage. 1. The batteries may be charged by connecting the supplied power adapter directly to the DC-in port on the system. 2. Open the cable cover and plug the cable directly into the connector. Then plug the adapter directly into the power outlet. The system will charge in the order of battery 1 to battery 3 and spend 5 hours charging time from 6% to 99% for each batery.
4-3. Battery Level Indication Each battery provides an battery level indicator LED on the front of the system.
4-4. Battery Discharging Mode Flowchart Battery discharging will be started from Battery1 when system boot on battery discharging mode.
5. 5-1. System Assembly Open the Cable Cover 1. Place the system face down, make sure not to scrath the screen. 2. Press and pull the cable cover outwards to release it from the system. 5-2. Open the Cable Cover 1. Power down the system first. Unplug the power adapter if connected directly to the DC-in port on the system. 2. Place the system face down, make sure not to scrath the screen. 3. Slide the latch down as shown to unlock. 4.
6. Specification Model Name Mainboard CPU Chipset System memory Graphic memory TPM 2.0 LAN controller (Giga LAN) LCD/Touch Panel LCD size Brightness Maximal resolution Touch screen type Storage HDD Flash memory Peripherals Web cam (option) MSR-right side(option) Expansion Mini PCIe socket M.
Model Name Mainboard Battery Battery Battery life *1 Charging time *2 Environment EMC & Safety Certification Operating temperature Storage temperature Operating altitude range Storage altitude range Humidity Dust & Water proof Dimensions (W x D x H) Weight (N.W.
7. Configuration 7-1.
7-2. Connectors & Functions Connector CN1/2 CN3 CN4 CN5 CN6 CN8/9/10 CN11 CN12 CN13 CN14 CN15 CN16 CN17 CN18 CN19 CN20 CN21 CN22 CN23 CN24 CN25 CN26 CN27/28 PCIE1 FAN1 HDMI AUX1 PWR1/PWR2 RJ11_1 RJ45_1 RJ45_2 RJ45_3 DiMM_A1 / DIMM_B1 SATA0/SATA1 BAT1 USB1/USB2 USB3 COM1 SW1 MINI_PCIE1 JP1 JP2 JP3 JP4/5 JP6 Function SATA power connector EC debug port Printer connector M.2 WiFi socket SDV connector USB2.
7-3. Jumper Setting Isolator USB(up port) speed select Function JP4 JP5 USB1.0 1 3 2 4 1 3 2 4 ▲ USB1.1 1 3 2 4 1 3 2 4 Isolator USB(down port) speed select Function JP4 JP5 USB1.0 1 3 2 4 1 3 2 4 ▲ USB1.
COM1/COM2 Power Setting COM1, COM2 can be set to provide power to your serial device. The voltage can be set to +5V or +12V in the BIOS. 1. Power on the system, and press the key when the system is booting up to enter the BIOS Setup utility. 2. Select the Advanced tab. 3. Select VGA/COM Power Configuration Ports and press to go to display the available options. 4. To enable the power, select COM1 ,COM2 Power setting and press . Select Power and press .
