USER MANUAL VERSION V1.
Copyright 2010 All Rights Reserved Manual Version 1.4 Part Number: 3LMPP7900214 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
CE MARK This device complies with the requirements of the EEC directive 2004/108/EC with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage Directive”. FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
LEGISLATION AND WEEE SYMBOL 2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components. The crossed dust bin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure.
Revision History Changes to the original user manual are listed below: Revision Description 1.0 1.1 1.2 1.3 1.4 •• •• •• •• •• •• •• •• •• •• •• •• •• •• Initial release Cover page update System View update System Installation update System Disassembly update Specification update Performance model info. added B68 motherboard Added B78 motherboard updated to v2.
Table of Contents 1. Packing List............................... 1 1-1. Standard Accessories...............................................1 1-2. Optional Accessories................................................2 2. System View.............................. 3 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. Front View................................................................3 Side View..................................................................3 Rear View with stand............................................
4-6. SSD Card Replacement..........................................15 4-6-1. On a Fan System..................................................... 15 4-6-2. On a Fanless System............................................... 16 4-7. Cash Drawer Installation ........................................17 4-7-1. For B78 motherboard............................................... 17 4-7-2. For B68/B98/C48 motherboard................................ 19 5. Specification............................ 21 6.
1. Packing List 11111 Standard Accessories aaa bbb ccc ddd eee fff System (with stand) Driver bank User guide Power adapter Power cord RJ45-DB9 cable (x2) a. b. c. d. e. f.
11111 Optional Accessories aaa bbb ccc ddd eee Metal MSR a. Metal VFD Wall-mount Kit SSD module WLAN Card (with internal antenna) b. c. a b c d. e.
2. System View 22222 Front View 1 2 22222 Side View 3 4 5 Fanless System Item No.
22222 Rear View with stand 7 6 8 Fan System Fanless System 9 22222 Rear View without wall mount bracket 10 Fan System Item No.
22222 I/O Ports View h c Fan System a b Item No. a b c d e f g h i j c a j d ef g j Fanless System i b h i de f g Description Parallel USB x 4 COM 1, 2, 3, 4 (from right to left) Line-out MIC-in Cash Drawer (12V or 19V, can support 24V) LAN Power Switch DC-In PS/2 Note: The I/O ports location may slightly different depending to the fan or fanless system installed.
22222 System Dimension 15" System 17" System 411 mm 308 mm 390 mm 386 mm 220 mm 220 mm 80 ° 62 mm 63 mm 370 mm 407 mm 80 ° 250 mm 250 mm 6
3. System Assembly To remove and replace the HDD, please follow below steps. The procedures may be different depending on the fan or fanless system being installed. 311. HDD replacement for fan system 1. Turn to the rear side of the system. 2. Unscrew the screw (x1) securing the HDD door and the rear cover of the system. 3. Disconnect the SATA cable from the drive. 312. HDD replacement for fanless system 1.
33333 RAM Replacement Please open the rear cover (see Chapter 3-1 or 3-2) first then remove and replace the RAM module. You can refer to the motherboard layout to find the memory compartment. (See chapter 6 for different motherboard) Removing a RAM module 111 Please Open the rear cover by unfasten the screws (x17) to access the motherboard. 222 Use both fingers to pull the ejector clips out of the sides of the module. 333 Slide out to take out the memory module from the memory slot.
314. Power Adapter Replacement 1. Disconnect the power cable from the adapter pre-installed in the power bracket attached in the stand. 2. Unscrew the screws (x2) and separate the power bracket from the stand. 3. Disconnect the other end of the power adapter from the connector on the I/O panel. 4. Draw out the power adapter gently through the cable management hole on the stand. 5. Replace the power adapter by reversing the procedure of above steps.
4. Peripheral Installation 44444 MSR Installation 111 Unfasten the thumb screws (x2) to remove the I/O cover. 222 Connect the MSR module into the system and fasten the screws (x2). 333 Connect the PS/2 Connector into the PS/2 port on the I/O panel. Note: the PS/2 port locates in different places on the I/O panel according to the fan or fanless system being installed.
44444 Wall Mount Kit Assembly Accessories items a. Metal bracket with thumb screw b. Screw x 1 c. Wall mount bracket a b c 111 Fix the metal bracket (a) to the VESA bracket and the display with the screw (b) (x1). 222 Align the tear drop holes of the wall mount bracket (c) into the 4 VESA bracket screws. 333 Fasten the thumb screw of the wall mount bracket (a) to fix the wall mount bracket (c) to the VESA bracket.
44444 Desktop Stand Assembly Accessories items a. VESA bracket b. Stand bracket c. Stand d. Hinge cover x2 e. Screws for both sides of stand x6 f. Screws for VESA bracket x 4 a b c d e f VESA bracket assembly 111 Align the standard VESA mounting holes of the VESA bracket (a) and the display and fix them with the screws provided (f) (x4). a f Stand bracket assembly b 222 Align the guide slot of the stand bracket (b) into the hinge shaft of the stand (c).
44444 Wireless LAN Installation 4-5-1. On a Fan System 111 Disconnect the HDD cable from the system first (see Chapter 3-1). a 222 Unscrew the screws (x17) to remove the rear cover (a). 333 Assemble the antenna cable (b) by fasten the nut, washer and the coaxial cable as picture instructs. 444 Insert the WLAN card (c) to the WLAN socket on the motherboard and press it downward until the ejector clips lock it in place. 555 Connect the antenna cable to the “main connector” on the WLAN card.
4-5-2. On a Fanless System For installing the external antenna and the wireless LAN card for fanless System, please see below pictures and instructions. 111 Open the rear cover by removing the screws (x17) a 222 Fix the antenna mounting bracket (b) with the screw (x1) onto the LCD chassis under the rear cover. 333 Assemble the antenna cable by inserting the coaxial cable to the pre-drilled hole of the bracket (b) and fastening with the nut and the washer with the mounting bracket.
44444 SSD Card Replacement If your system equipped with SSD Card instead of hard drive disk as storage device, please follow below steps to replace the SSD card. 4-6-1. On a Fan System 1. Fasten the screw(x4) on the rear side of the SSD holder bracket to fix the SSD card. 2. Turn to the rear side and open the HDD door on a fan system (see Chapter 3-1). 3. Fasten the screw (x3) as shown to fix the SSD module.
4-6-2. On a Fanless System 1. Follow 4-6-1 step 1 to assemble SSD module. 2. Turn to the rear side and open the rear cover on a fanless system (see Chapter 3-2). 3. Fasten the screw (x4) as shown to fix the SSD module.
44444 Cash Drawer Installation 4-7-1. For B78 motherboard You can install a cash drawer through the cash drawer port. Please verify the pin assignment before installation. Cash Drawer Pin Assignment Pin 1 2 3 4 5 6 6 Signal GND DOUT bit0 DIN bit0 12V / 19V DOUT bit1 GND 1 Cash Drawer Controller Register The Cash Drawer Controller use one I/O addresses to control the Cash Drawer.
Bit 7: Reserved. Bit 6: Reserved. Bit 5: Reserved. Bit 4: Cash Drawer “DIN bit0” pin input status. = 1: the Cash Drawer closed or no Cash Drawer. = 0: the Cash Drawer opened. Bit 3: Reserved. Bit 2: Cash Drawer “DOUT bit0” pin output control. = 1: Opening the Cash Drawer = 0: Allow closing the Cash Drawer Bit 1: Cash Drawer “DOUT bit1” pin output control.
4-7-2. For B68/B98/C48 motherboard You can install a cash drawer through the cash drawer port. Please verify the pin assignment before installation. Below cash drawer installation is applicable for B68, B98 and C48 motherboard. Cash Drawer Pin Assignment Pin 1 2 3 4 5 6 6 Signal GND DOUT bit0 DIN bit0 12V / 19V DOUT bit1 GND 1 Cash Drawer Controller Register The Cash Drawer Controller use one I/O addresses to control the Cash Drawer. The Cash Drawer Control Register and the Cash Drawer Status Register.
Bit 7: Reserved Bit 6: Cash Drawer “DIN bit0” pin input status. = 1: the Cash Drawer closed or no Cash Drawer = 0: the Cash Drawer opened Bit 5: Reserved Bit 4: Reserved Bit 3: Cash Drawer “DOUT bit1” pin output control. = 1: Opening the Cash Drawer = 0: Allow close the Cash Drawer Bit 2: Cash Drawer “DOUT bit0” pin output control.
5. Specification Motherboard B68 Fan/Fanless Fanless CPU Support Chipset System Memory Graphic Memory Share system memory up to 224MB Touch Screen Type Tilt Angle Storage HDD Flash Memory External I/O Ports USB PS2 Serial / COM Parallel LAN (10 /100 / 1000) DC Jack Intel Celeron M 1.5GHz / Pentium M 1.8GHz (Socket) Shared system memory up to 64MB Shared system memory up to 224MB C48 Fanless Intel Pineview D525 dual core 1.
Motherboard Cash Drawer Port Audio Jack Audio Built in Speaker B68 B78 1 x RJ 11 (12V /19V) 1 x Line-out, 1 x Mic-in N/A N/A 2x2W B98 C48 2x2W N/A Power Power Adapter 19V, 90W Control Power Button Peripheral 1 Metal MSR 3 Tracks MSR ( PS/2 ) Metal Customer Display Flush mount VFD display 2 x 20 characters (COM) Communication Wireless LAN 802.
6. Jumper Setting 66666 For B68 Motherboard 6-1-1. Motherboard Layout Version: B68 v1.
6-1-2.
Connector SATA2 SKT1 USB1 USB2 SW1 JP1 JP2 JP3 Purpose SATA Connector SPI ROM USB1, USB2 USB3, USB4 Power On Bottom CRT Connector CRT Power/I2C Connector COM3/COM4 Power Setting JP4 JP5 JP6 JP7 JP8 JP9 JP11 JP12 VGA Power Setting COM2 Connector COM2(RS232/422/485) Setting LCD ID Setting RTC Reset Power Mode Setting Cash Drawer Power Setting (+12V,+19V) Hardware Reset 25
6-1-3.
Cash Drawer Power Setting Function JP11 ▲+12V 1 3 2 4 +19V 1 3 2 4 Power Mode Setting Function ▲ATX Power AT Power JP9 1 2 1 2 RTC Reset Function JP8 ▲CMOS Normal 1 2 CMOS Reset 1 2 VGA Power Setting Function JP4 ▲No Power 1 2 +12V 1 2 ▲ = Manufacturer Default Setting 27
LCD ID Setting LVDS Output Channel Interface Panel# Resolution 1 1366 x 768 24 Single LVDS Panel 1 3 5 7 2 4 6 8 2 1440 x 900 24 Dual LVDS Panel 1 3 5 7 2 4 6 8 4 1920 x 1080 24 Dual LVDS Panel 1 3 5 7 2 4 6 8 5 1024 x 768 24 Single LVDS Panel 1 3 5 7 2 4 6 8 6 1280 x 1024 24 Dual LVDS Panel 1 3 5 7 2 4 6 8 7 800 x 600 24 Single LVDS Panel 1 3 5 7 2 4 6 8 9 1024 x 768 18 Single LVDS Panel 1 3 5 7 2 4 6 8 11 800 x 600 18 Single LVDS Panel 1 3 5 7 2 4 6 8 12
66666 For B78 Motherboard 6-2-1. Motherboard Layout Version: B78 v2.
6-2-2. Connectors & Functions Connector Purpose CN1 Audio Line Out CN2 Audio MIC In CN3 Internal Power Switch CN4 Speaker & MIC Connector CN9 CD-IN Connector CN11 Power Connector For 3.
6-2-3.
Cash Drawer Power Setting Function ▲+12V 1 3 5 2 4 6 +19V 1 3 5 2 4 6 Power Mode Setting Function ▲ATX Power AT Power CMOS Operation Mode Function ▲CMOS Normal CMOS Reset USB Path Setting Function ▲To Docking To Motherboard System Indicator Function Function JP6 1 2 1 2 JP8 1 2 1 2 JP14 1 2 1 2 JP13 ▲Disable 1 3 5 7 2 4 6 8 Enable 1 3 5 7 2 4 6 8 ▲ = Manufacturer Default Setting 32 JP4
LCD ID Setting LVDS Channel Panel# Resolution 1 640 x 480 18 Single 1 3 5 7 2 4 6 8 2 800 x 600 18 Single 1 3 5 7 2 4 6 8 3 1024 x 768 18 Single 1 3 5 7 2 4 6 8 4 1280 x 1024 24 Dual 1 3 5 7 2 4 6 8 5 1024 x 768 24 Single 1 3 5 7 2 4 6 8 6 800 x 600 24 Single 1 3 5 7 2 4 6 8 7 800 x 600 18 Single 1 3 5 7 2 4 6 8 8 800 x 600 18 Single 1 3 5 7 2 4 6 8 9 1024 x 768 24 Single 1 3 5 7 2 4 6 8 10 1440 x 900 24 Dual 1 3 5 7 2 4 6 8 11 1280 x 1024 24 Dual 1 3
613. For B98 Motherboard 61311. Motherboard Layout Version: B98 v1.
6-3-2.
6-3-3.
Cash Drawer Power Setting Function JP3 ▲+12V 1 3 5 2 4 6 +19V 1 3 5 2 4 6 Power Mode Setting Function ▲ATX Power AT Power CMOS Operation Mode Function JP11 1 2 1 2 JP7 ▲CMOS Normal 1 2 CMOS Reset 1 2 System Indicator Function ▲Disable Enable JP12 1 3 5 7 2 4 6 8 1 3 5 7 2 4 6 8 ▲ = Manufacturer Default Setting 37
LCD ID Setting LVDS Output Channel Interface Panel# Resolution 1 1366 x 768 24 Single LVDS Panel 1 3 5 7 2 4 6 8 2 1440 x 900 24 Dual LVDS Panel 1 3 5 7 2 4 6 8 4 1920 x 1080 24 Dual LVDS Panel 1 3 5 7 2 4 6 8 5 1024 x 768 24 Single LVDS Panel 1 3 5 7 2 4 6 8 6 1280 x 1024 24 Dual LVDS Panel 1 3 5 7 2 4 6 8 7 800 x 600 24 Single LVDS Panel 1 3 5 7 2 4 6 8 9 1024 x 768 18 Single LVDS Panel 1 3 5 7 2 4 6 8 11 800 x 600 18 Single LVDS Panel 1 3 5 7 2 4 6 8 12
66666 For C48 Motherboard 6666666 Motherboard Layout Version: C48 v2.
6666666 Connectors & Functions Connector CN1 CN3 CN4 CN5/8 CN11 CN13 CN14 CN15 CN16 CN17 CN18 CN19 CN20/JP10 CN21 CN22 CN23 CN24 CN25 CN26 CN27 CN28 CN29 DDR3_A1 SATA1 SATA2 SW1 JP1 JP3/6 JP4/5 JP8 JP9 JP12 JP14 JP18 JP19 40 Purpose Power Button Connector Printer Port Reset Printer Port HDD Power COM5 For Touch Card Reader Connector Line out HDD LED Speaker & MIC CD IN MIC IN Power LED System Indicator LAN LED USB Port PS2 KEYBOARD +19V DC IN For GM2621 Debug LVDS Inverter Connector Key Pad System Fan DDR
6666666 Jumper Setting COM2 RS232/485/422 Setting Function JP5 JP4 ▲RS232 1 3 5 7 9 2 4 6 8 10 1 3 5 7 9 11 2 4 6 8 10 12 RS485 1 3 5 7 9 2 4 6 8 10 1 3 5 7 9 11 2 4 6 8 10 12 RS422 1 3 5 7 9 2 4 6 8 10 1 3 5 7 9 11 2 4 6 8 10 12 Cash Drawer Power Setting Function JP19 +19V 1 3 2 4 ▲+12V 1 3 2 4 Power Mode Setting Function JP9 1 2 ▲ATX Power 1 2 AT Power System Reset Function JP12 ▲System Normal 1 2 System Reset 1 2 ▲ = Manufacturer Default Setting 41
System Indicator Function JP10 ▲Disable 1 3 5 7 2 4 6 8 Enable 1 3 5 7 2 4 6 8 Inverter Selection Function JP14 ▲ CCFL 1 3 5 2 4 6 LED 1 3 5 2 4 6 CMOS Operation Mode CMOS Reset To clear the CMOS, 1. Remove the power cable from the system. 2. Open the system, and set the ‘CMOS Operation jumper’ from ‘CMOS Normal’ to ‘CMOS Reset’. (refer to the jumper shown below) 3.
COM3 & COM4 Power Setting For C48, COM3/COM4 power adjustment must be made by BIOS/Utility and Jumper. Since COM3/COM4 default is “None“ meaning no power, power must be on through BIOS prior to physical jumper change. BIOS/Utility setup 111 Press key to enter BIOS SETUP UTILITY when system boot up. 222 Find tab "Advanced". 333 Select "Power Configuration COM/VGA Ports" and press to go to sub screen. 4. To switch on the power, select "Power".
LCD ID Setting Several configurations are applied to different sizes of panel. Please refer to the followings to complete relevant settings. 12.
4. To switch on the power, select "+12V". Please save the change before exiting BIOS to avoid data lost. 5. To switch brightness level, select brightness control and choose level. Please save the change before exiting BIOS to avoid data lost.
Appendix: Drivers Installation The shipping package includes a Driver CD in which you can find every individual driver and utility that enables you to install the drivers on the system. Please insert the Driver CD into the drive and double click on the “index.htm” to select the models. You can refer to the drivers installation guide for each driver in the “Driver/Manual List”.
