User Manual Version 1.
Copyright 2012 All Rights Reserved Manual Version 1.0 Part Number: The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Safety IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. To disconnect the machine from the electrical Power Supply, turn off the power switch and remove the power cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the machine. Read these instructions carefully. Save these instructions for future reference. Follow all warnings and instructions marked on the product. Do not use this product near water.
CAUTION ON LITHIUM BATTERIES There is a danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. Battery Caution Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery according to the local disposal instructions. Safety Caution Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.
The crossed dustbin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Revision History Revision Date V1.
Table Contents 1 Package Checklist .................................1 1-1 Standard Items .................................................................. 1 2 System View ............................................2 2-1 2-2 2-3 2-4 2-5 Front View........................................................................... 2 Side View............................................................................ 3 Rear View ...........................................................................
1 1-1 Package Checklist Standard Items a. System b. Phone module c. Power adapter d. Power cable e. Driver CD f.
2 2-1 System View Front View ` Number Description 1 Build-in camera 2 Camera LED 3 Touch screen 4 Touch keys (from left to right: volume down, volume up, power button, channel down, channel up) 5 Smart IC card reader 6 VOIP phone (optional) 2
2-2 Side View Number 2-3 Description 1 Combo smart IC card reader with separate RFID antenna (optional) 2 Speaker Rear View Number Description 1 Light Sensor 2 Webcam switch 3 Ventilation 4 SSD card door 5 Cable cover 6 Vertical I/O port (from left to right: Nurse call, Display port, DC jack, USBx2, LAN ) 7 VESA hole for wall-mount kit installation 3
2-4 Bottom View Number 1 Ventilation 2 From left to right: Video in, Audio left, Audio right (optional) 3 2-5 Description Bottom I/O port (from let to right: LAN, USBx2, Remote, Power button) 4 Microphone 5 Smart IC card reader 6 USBx1 7 Phone jack (RJ11) 8 From left to right: Audio line-out, Mic-in, Audio line-out Dimension 4
3 3-1 System Assembly SSD Card Replacement 1. Find the SSD card door at the rear right side of the system and remove the screws(x1) 2. To replace the SSD card, remove the screws (x4) and push the SSD card outwards as shown in the picture.
4 4-1 Peripheral Installation Phone module Installation 1. Loosen the screw(x1) to open the cable cover. 2. Slide the phone module into the phone holder and connect the other end of the phone cable to the connector on the system.
4-2 Wall Mount Installation 1. 2. Connect the cables to the system. Fasten the screws.(monitor screwx4) Note: For use only with UL listed wall mount bracket with minimum support weight/load: 5.
5 Specification Model PA79 Motherboard C43 Processor Pineview D525 Core Logic CPU with Graphic built-in + ICH 8M System Memory 2 x DDR3 SO-DIMM slot up to 4GB FSB800Mhz Graphic Memory Intel GMA 3150 share system memory up to 256MB LAN Controller / PHY Intel WG82583V / Intel WG82567V Audio Controller Realtek ALC 662-GR HD codec I/O Controller Winbond W83627UHG Touch TF P-cap 18.
Model PA79 Motherboard C43 Mic-In 1 (Auto-detect,GPIO), in external IO Vertical I / O LAN 1 x RJ45 (with 10/100/1000) Power DC Jack Display Port 1 USB 2 (USB 2.
6 6-1 Jumper Settings C43 motherboard layout 10
6-2 Connectors & Functions Connector Function CN3 USB Port For Web Cam CN4 Speaker & MIC CN5 Cradle CN6 Speaker CN7 Audio Jack (Line out & MIC) CN9 Inverter CN10 Build-In MIC CN12 Nurse Call Button CN14 Membrane CN15 30P All-In-One (Membrane, 2D scanner, RFID, Smart card, Audio Jack) CN17 Nurse Call LED Power CN18 Audio Jack (Line Out) CN19/JP5 System Indicator CN20 IrDA CN21 LVDS CN22 Power LED CN23 PS/2 Keyboard CN24 MSR CN25 COM1 CN26 System FAN CN27 MIC for AE
Connector Function RJ48_3 Nurse Call SATA1/2 SATA SCSI_3 Remote Control USB3 USB3 USB4 USB1, USB2 of HUB USB5 USB1, USB2 JP3 Touch JP4 Inverter Selection JP6 LCD ID Setting JP7 MCU Power Button JP8 Power Mode Setting JP9 MCU Mode Setting JP10 System Reset JP11 CMOS Operation Mode 12
6-3 Jumper Setting Inverter Selection Function JP4 (1-2) (3-4) (5-6) CCFL ▲LED System Indicator JP5 Function (1-2) (3-4) (5-6) (7-8) ▲Disable Enable MCU Power Button Function JP7 (1-2) Disable ▲Enable Power Mode Setting Function JP8 (1-2) ▲ATX Power AT Power 13
MCU Mode Setting Function JP9 (1-2) ▲Normal ISP Debug System Reset Function JP10 (1-2) ▲System Normal System Reset CMOS Operation Mode Function JP11 (1-2) ▲CMOS Normal CMOS Reset ▲ = Manufacturer Default Setting Note: OPEN SHORT 14
7 Drivers Installation The shipping package includes a Driver CD. You can find every individual driver and utility that enables you to install the drivers in the Driver CD. Please insert the Driver CD into the drive and double click on the “index.htm” to pick up the models. You can refer to the drivers installation guide for each driver in the “Driver/Manual List”.
