User's Manual

LED
FS-SPD01
SPEED
2
OUT
IN
Magnetic
15
FS-CEV04 i-BUS 串行总线接收机连接说明
FS-CPD01 磁感应转速采集模块 RPM telemetry (magnetic) module setup
传感器 Sensor
速度采集模块
Revolving
speed module
齿轮
Gear
磁铁
Magnet
行总线接收多可4个模,共16通道按键K1-K4分别C1-C4, 用于相应道的定;
作说
1. FS-CEV04 i-BUS机的IN”端口对接收的“OUT”端
2. FS-CEV04 i-BUS机的OUT端口用于接后FS-C EV0 4收机以串的 方式使用。
3. 将此线接收机入接机,开己对的射机接收电源LED亮;
4. 操作射机触控,选接收设定主菜,进到舵设定界面
5. 选择要扩展的道,时,线接机的LED熄灭
6. 用对线上的胶,按需要,相通道按键LED动点,表设定功;
7. 插入机,检查定是成功
8. 重复上操作即完成线接4个通的设
9. 当需更多的通扩展,只要在一级线接机的OUT端口串接的总线接收即可设定的操方法同。
意: 当总线机的重,大时将主的电出来入,供电载的
可能电流烧坏线材
使用
1. 将所3 PIN,一插入采集OUT”位,另插入收机IN”
另外应器IN置,12.4示;
2. 如图12.5将传器放铁的边,固定需要的轴转动方,直升
齿 轮上面感器磁铁两毫以内极或与传器保行。
3. 打开射机收机,在示屏收机口内发现显示“Motor speed 2:0RPM”,
着转转速值会变化则表装成
(Pic 12.3)
(Pic 12.4)
(Pic 12.5)
i-BUS receiver, can connect 4 modules with 16 channels in serial at most. Button K1 and K4 correspond to C1 and C4
respectively.
Operation instruction:
1. FS-CEV04 i-BUS The “IN” port of FS-CEV04 receiver corresponds to “OUT” port of receiver.
2. FS-CEV04 i-BUS The “OUT” port of FS-CEV04 receiver is used to connect post level
FS-CEV04 receiver.
3. Insert the bus receiver to receiver, and then switch on the matched transmitter and receiver. The LED will be on.
4. Select main menu of receiver setup to enter the interface of servo setup.
5. Select channel which need to be expanded, meanwhile LED of bus receiver is off.
6. Push relevant channel button by plastic needle of matching line. The setup is successful if LED flashes automatically.
7. Insert servo to check.
8. Set up 4 channels of bus receiver as above steps.
9. Just connect a new bus receiver with “OUT” port of first stage bus receiver if more channel needed. Set up the new one as
above steps.
Notice: When the load of serial bus receiver is excessive and electric current is higher than usual, please supply power
directly to the serial bus receiver or it will break cables.
Operation:
1. Insert one end of standard 3 PIN plug into “OUT” port of RPM telemetry (magnetic)
module, and insert the other end into “IN” port of receiver or other sensor, as shown
in the picture 12.4.
2. As shown in the picture 12.5: Inside hub of the model, the distance between sensor
and magnet is less than2mm. The North Pole or the south pole of the magnet has
to be paralleled with sensor.
3. Switch on transmitter and receiver. “Motor speed 2:0RPM” will be shown in receiver
window in display screen. Speed value changes as turning wheel, which means
installation is successful.
说明
功能为了应对些模通道多而的,通道够时采用此配件,来增加道输
说明
功能了检到模转速设定用户通过机来察监模 型的转,当需要测转可使此配
The system is able to support many channels. This allows the user of the system to change to a different
output channel should signal strength be insufficient
This function allows the user to monitor turning speed via the transmitter. This is a
very useful function when determination of turning speed is required
Function Details
Function Details
i-bus Receive r Connection instruc tion Setup
5