Vision Compact 350 Plus TIO A M R N FO N I ANT T R nce e O e s r P u e f e M I efor uture re b d a Re or f f n i ta & re For all customer enquiries or for replacement parts, contact:- 0870 609 1901 www.flymo.com customer.services@husqvarna.co.
Carton Contents switchbox start/stop levers Easi Reel cable winder cable winder attachment cable clip bolt washer upper handle handle knobs cable clip electric cable with moulded plug pack of 10 bags nuts washer pin bolt retaining clips lower handle cutting height spacers (1 fitted to lawnmower & 2 in loose parts pack pin instruction manual spanner/scraper tool IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
. Do not use the lawnmower if the electric cables are damaged or worn 4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one. 5. Your extension cable must be uncoiled, coiled cables can overheat and reduce the efficiency of your mower. 6.
Assembly Instructions A B 1 2 1 3 C D 2 1 1 2 Lower Handle Assembly (A) 1. Lift the grassbox lid and remove the grassbox. 2. Insert the lower handle into the handle slots, ensuring that the holes are aligned. 3. Insert the pins and secure with the retaining clips (A1). 4. Replace the grassbox, and lower the grassbox lid carefully. Upper Handle Assembly (B) 1. Insert the nut into the handle knob (B1). 2.
Starting and Stopping F G H J K To Start your Lawnmower Your lawnmower uses an advanced belt drive system, between the motor and the blade which improves cutting power and flotation in all conditions. Due to the high turning force (Torque) which this motor develops a light squeak may be heard when the machine is started, this is quite normal and will not effect the performance of the product 1. Connect female extension cable connector to the back of the switchbox. (F) 2.
Removing and fitting the Blade and Fan N blade bolt blade spacers fan Removing the Blade and Fan 1. To remove the blade bolt, hold the fan firmly and with the spanner provided loosen the blade bolt by turning it anti-clockwise (M). 2. Remove the blade bolt, blade, spacers and fan. (M) 3. Inspect for damage and clean as necessary. • Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner - regardless of condition. If the blade is cracked or damaged replace it with a new one.
Caring for your Lawnmower Cleaning IMPORTANT: It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the hood could become a potential fire hazard. USE GLOVES. Switch off and remove the plug from the mains before cleaning. It is recommended that you clean your lawnmower straight after mowing while the grass is still wet. 1. Remove grass from under the hood with the spanner/scraper tool. (T1) 2.
Fault Finding Hints Fails to Operate 1. Is the correct Starting procedure being followed? See ‘To Start your Lawnmower’ 2. Is the Power Turned On? 3. Check the fuse in the plug, if blown replace. 4. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Poor Flotation 1. Disconnect from the mains electricity supply. 2. Clean the underside of the hood and the fan blades. 3. Raise to a higher height of cut.
Environmental Information Husqvarna Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products’ life. • Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.
