SAMURAI 1000XT AUTOMATIC SPEED CONTROL FOR YOUR SAFETY AND COMFORT TIO RMA N NFO I T TA N se R O ence r P u e f e M e r I efo re r b u t d u a f Re n for i a t e &r For all customer enquiries or for replacement parts, contact:- ☎ 0870 609 1901 www.flymo.com customer.services@husqvarna.co.
Carton Contents Cable Management Shoulder Harness Location Handle Clamp Instruction Manual Electric Cable with moulded on plug Lock-off button Cable Management Adjustable Shoulder Harness Switch Handle Hexagon Drive Tool Guard (with bolt and nut) Steady Handle IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
. Do not use the product if the electric cables are damaged or worn. 4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one. 5. Your extension cable must be uncoiled, coiled cables can overheat and reduce the efficiency of your product. 6. Keep the cable clear of the cutting area and obstacles at all times.
Assembly Instructions A Switch Handle and Handle Tube Assembly (A), (B) & (C) 3 4 1. Loosen the four bolts on the Handle Clamp (A). 2 1 B1 2. Insert the Switch Handle and the Steady Handle into the holes at the side of the Handle Clamp (B1 Right Handed) (B2 Left Handed) - using the Hex Drive Tool to turn the switch handle (B3) B3 B2 C 3 4 2 1 D 3 2 E 2 3. Adjust the Handles to the most comfortable operating position by moving the Handle Clamp up or down the tube. 4.
Assembly Instructions cont’ J1 J2 K1 K2 Cable Restraint 1. Form loop in mains cable and push the loop through the slot (J1). 2. To secure, position loop over the hook and pull the cable back through the slot (J2). Adjustable Shoulder Harness 1. Attach the clip on the Shoulder Harness to one of the holes in the Shoulder Harness Location (K1) to enable the correct and most comfortable balance when using the product with the harness fitted across the body (K2) Line Cutter Cover 1.
Cutting Head To replace nylon line. For your convenience it is recommended you buy spool and line complete. Nylon line only is also available. Both are available from Husqvarna Outdoor Products stockists. To fit spool and line complete: 1. Remove the Cap (Q1) and Spool Holder (Q2) 2. Remove old spool.(R) 3. Place new spool into spoolholder.(R) 4. Release one line from cleat (W). 5. Secure line into eyelet (S1). 6. Repeat for second line. 7. Refit the Spoolholder and fit the Cap ensuring it is secure.
Maintenance • WARNING Disconnect from the mains electricity supply, before attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your Product 1. Disconnect from the mains electricity supply. 2. Never clean your product with water, cleaning fluids, or solvents, just remove debris with a suitable tool, a soft brush or dry cloth. 3.
Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT LINE NOT FEEDING OR LINE TOO SHORT OR TRIMMER VIBRATES CONTINUOUS CLATTERING NOISE LINE SNAPS CONTINUOUSLY IF NONE OF THE ABOVE OR IF FAULT PERSISTS CHECK ACTION Remove cap and spool, free line and re-fit spool and cap.
Guarantee & Guarantee Policy If any part is found to be defective due to faulty manufacture within the guarantee period, Husqvarna Outdoor Products, through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing: (a) The fault is reported directly to the Authorised Repairer. (b) Proof of purchase is provided. (c) The fault is not caused by misuse, neglect or faulty adjustment by the user. (d) The failure has not occurred through fair wear and tear.
