Pac a Mow TIO A M R N NFO I T TA N se ce R n O e r P u e f I M before e re r u t d u Rea in for f ta & re For all customer enquiries or for replacement parts, contact:- ☎ 0870 609 1901 www.flymo.com customer.services@husqvarna.co.
1 Carton Contents cable hook x 2 upper handle screw x 2 round headed bolt x 2 barrel nut x 4 electric cable with moulded on plug cam lock x 4 washer x4 lower handle cable clip grassbox square headed bolt x 2 pivot block x 2 spring x 2 spanner instruction manual IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
2 there are signs of damage or ageing. 3. Do not use the lawnmower if the electric cables are damaged or worn 4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one. 5. Your extension cable must be uncoiled, coiled cables can overheat and reduce the efficiency of your mower. 6.
Assembly of Lower Handles to Lawnmower A1 A2 A3 1. Insert the Square Headed Bolt into the lawnmower as illustrated in fig A1. Then push the Bolt down until it is locked into position as illustrated in fig A2. 2. Place the Spring over the Bolt (A3) 3. Insert the Pivot Block on to the Bolt (A4) B C2 A4 C1 C3 pivot block lower handle x3 washer cam lock 4. Place the Lower Handle over the deck as illustrated in fig B. 5. Insert the Barrel Nut into the Cam Lock as illustrated in fig C1. C4 C5 7.
D4 D5 D6 4. Fold down the Cam Lock towards the Handle as illustrated in fig D4, and continue to turn clockwise (D5) until tightened. E F 1 5. The Cam Lock can be unlocked and locked as illustrated in fig D6. Repeat for the other side. G H 2 Attaching the Cable Hooks (for storage of the mains cable) 1. Insert the post on the Cable Hook (E1) through the hole in the Upper Handle (E2). 2. Insert the Screw and tighten to secure (F) Repeat for the other side.
M N Starting and Stopping P Q 1 To Start your Lawnmower 1. Form loop in mains cable and push the loop through the slot. (M) 2. To secure, position loop over the hook and pull the cable back through the slot (N). 3. Connect plug to mains and switch on. 4. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting. The switchbox is provided with a Lock-Off Button (P1) to prevent accidental starting. 5.
Caring for your Lawnmower T Cleaning (T) • USE GLOVES • IMPORTANT It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the lawnmower could become a potential fire hazard. 1. Remove grass from under the lawnmower with brush. 2. Using a soft brush - remove grass clippings from all air intakes, the discharge chute and the grass box. 3. Remove the Blade, see Figure S, to gain access to V1 the Fan and clean with a soft brush. 4.
Fault Finding Hints Fails to Operate 1. Is the correct Starting procedure being followed? See ‘To Start your Lawnmower’ 2. Is the Power Turned On? 3. Check the fuse in the plug, if blown replace. 4. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Poor Grass Collection 1. Disconnect from the mains electricity supply. 2. Clean the outside of the air intakes, the discharge chute and the underside of the deck. 3.
EC Declaration of Conformity I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP. Certify that the product:Category........ Electric Wheeled Rotary Make...........Husqvarna Outdoor Products Conforms to the specifications of Directive 2000/14/EEC I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham.
