Multimo 360 Multimo 360XC Original Instructions TION A M R INFO TA N T e R O P IM ore us ure reference f e b d Rea in for fut & reta For all customer enquiries or for replacement parts, contact:- 0870 609 1901 www.flymo.com customer.services@husqvarna.co.
Carton Contents start/stop lever switchbox cable clip x 2 lock off button grassbox upper grassbox handle upper handle washer x4 Multimo 360 bolt cam lock x 4 roller half x 2 lower handle x 2 barrel nut x 4 grassbox half x 2 pivot block x 2 electric cable with moulded on plug spring x 2 instruction manual mulching plug start/stop lever switchbox cable clip x 2 washer x4 cam lock x 4 Multimo 360XC lock off button grassbox handle upper handle Easi-Reel cable spool grassbox upper bolt rol
Safety If not used properly this product can be dangerous! This product can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this product. The operator is responsible for following the warning and safety instructions in this manual and on the product. Never use the product unless the grassbox or guards provided by the manufacturer are in the correct position.
surfaces other than grass. 11. Never operate the product with damaged guards or without guards in place. 12. Keep hands and feet away from the cutting means at all times and especially when switching on the motor. 13. Do not tilt product when the motor is running, except when starting and stopping. In this case, do not tilt more than absolutely necessary and lift only the part which is away from the operator.
Roller Assembly B2 B1 1. Turn product over. 2. Place both halves of the roller over the location pegs as illustrated in fig.B1 3. Clip the roller together to secure it into position.(B2) • Do not clip the roller together before placing over the location pegs Assembly of Lower Handles to Lawnmower C2 C3 C1 1. Pull the lower handle bolt until it locks into position as illustrated in fig C1. 2. Place the Spring over the Bolt (C2) D1 3.
D5 Assembly of Lower Handles to Lawnmower (cont’) D6 7. Ensuring the raised markings on the Cam Lock and the deck are aligned (D5), fold down the Cam Lock towards the Handle as illustrated in fig D6, and continue to turn clockwise (D7) until tightened. D7 Repeat for the other side. D8 8. The Cam Lock can be unlocked and locked as illustrated in fig D8. Assembly of Upper Handles to Lower Handles E1 E2 E3 x3 1. Insert the Barrel Nut into the Cam Lock as illustrated in fig E1. 2.
Grassbox Assembly (cont’) Grassbox Assembly 1. Locate the the grassbox halves together by aligning the clips Ensure all clips are correctly located before clicking into position. (G1) 2. Locate the grassbox lid onto the assemble grassbox by aligning the clips. Ensure all clips are correctly located before clicking into position (G2) Fitting Fully Assembled Grassbox to Lawnmower. 1. Lift safety flap (H1) 2. Make sure the discharge chute is clean and free from debris (H2) 3.
Grassbox Full Window N grassbox empty grassbox full • As the grassbox fills up, grass will be visible through the window (N). • When the window/grassbox is full it is time to empty the grassbox. Mulching Plug P1 P2 Using as a mulcher P3 1. Your lawnmower is supplied with a mulching plug. (P1) 2. Stop your lawnmower as described in Starting and Stopping. 3. Lift safety flap and insert the mulching plug into rear discharge chute. (P2) ensuring it is securely fitted. (P3) 4.
Starting and Stopping (cont’) V 6. Continue to squeeze the start/stop lever towards the upper handle and release the lock-off button (W). 7. Lower the lawnmower to its proper operating position and commence mowing. • NOTE - There are two start/stop levers fitted. Either one can be used for starting the lawnmower. • IMPORTANT - Do not use the start/stop levers intermittently To Stop your Lawnmower 1. Release the pressure on the Start/Stop lever.
Caring for your Lawnmower Z1 Z2 Cleaning • USE GLOVES • IMPORTANT:- It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard. 1. Remove grass from under the deck with brush. (Z1) Z3 Z4 2. Using a soft brush - remove grass clippings from all air intakes (Z2), the discharge chute (Z3) and the grass box (Z4). 3. Using a soft brush, remove grass clippings from the vision window (Z5). 4.
Fault Finding Hints Fails to Operate 1. Is the correct Starting procedure being followed? See ʻTo Start your Lawnmowerʼ 2. Is the Power Turned On? 3. Check the fuse in the plug, if blown replace. 4. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre. Poor Grass Collection 1. Disconnect from the mains electricity supply. 2. Clean the outside of the air intakes, the discharge chute and the underside of the deck. 3.
EC Declaration of Conformity Husqvarna UK Ltd., Aycliffe Industrial Park Newton Aycliffe, Co. Durham, DL5 6UP, England Declare under our sole responsibility that the product(s); Category............................Electric Rotary Lawnmower Type(s) ............................MM360, MM360XC Identification of Series.......See Product Rating Label Year of Construction..........See Product Rating Label Conforms to the essential requirements & provisions of the following EC Directives: 98/37/EC (until 31.12.
