EasiCut 420/EasiCut 450/ EasiCut 500/EasiCut 510 EasiCut 600XT Original Instructions EasiCut 420/450/500/510 EasiCut 600XT TIO A M R N NFO I T TA N se R nce O e P r u e f e M r e I befo future r d a e R n for i a t e &r For all customer enquiries or for replacement parts, contact:- 01325 300303 www.flymo.com customer.services@husqvarna.co.
Carton Contents EasiCut 420/450/500/510 Handguard blade cover instruction manual belt clip EasiCut 600XT Handguard blade cover instruction manual belt clip IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new product. IF ANY PARTS ARE MISSING CONTACT:Husqvarna UK Ltd.
Safety If not used properly this product can be dangerous! This product can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this product. The operator is responsible for following the warning and safety instructions in this manual and on the product. Explanation of Symbols on your product Warning. Read the user instructions carefully to make sure you understand all the controls and what they do.
Safety cont’ use. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5.
Cables CABLES IMPORTANT • Use only 1.00mm2 size cable up to 40 metres length maximum. Maximum rating : 1.00mm2 size cable, 10 amps 250 volts AC. • YOUR HEDGETRIMMER IS SUPPLIED WITH CABLE WIRED DIRECTLY INTO THE PRODUCT. 1. Mains Cables and Extension Cables are available from your local Approved Service Centre. 2. Do not wire an extension cable directly to your product yourself. Please contact your local Approved Service Centre for further information on the connectors and kits available. 3.
Before Use B1 B3 B2 C1 C2 D Before starting your hedge trimmer. • Securing the cable in the Belt Clip helps keep the cable away from blade. 1. Push up the hook on the Belt Clip (B1) 2. Place the rear section of the Belt Clip behind your belt (B2) 3. Push down the hook on the Belt Clip to secure it onto your belt (B3) 4. Form a loop in the mains cable and push the loop through the hole in the Belt Clip (C1) ensuring the coil in the cable is close to the clip. 5.
How to Use How to Use your hedge trimmer 1. Inspect area to be cut before each use - remove objects which can be thrown or become entangled in the cutting blades. 2. Always keep the hedge trimmer in front of your body. Hold handle firmly with both hands and stand in a secure and stable position. 3. Allow the cutting blades to reach full speed before entering the material to be cut. 4. Always work going away from people and solid objects such as walls, large stones, trees, vehicles etc. 5.
Environmental Information • • Awareness of the environment must be considered when disposing of ʻend-of-lifeʼ product. If necessary, contact your local authority for disposal information. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and elec- tronic equipment.
EC Declaration of Conformity Husqvarna UK Ltd., Aycliffe Industrial Park Newton Aycliffe, Co. Durham, DL5 6UP, England Declare under our sole responsibility that the product(s); Category............................Hedgetrimmer Type(s) ............................EC420, EC450, EC500, EC510, EC600 Identification of Series.......See Product Rating Label Year of Construction..........See Product Rating Label Conforms to the essential requirements & provisions of the following EC Directives: 98/37/EC (until 31.
