SAMURAI 800/1000 AUTOMATIC SPEED CONTROL FOR YOUR SAFETY AND COMFORT TIO RMA N NFO I T TA N se R O ence r P u e f e M e r I efo re r b u t d u a f Re n for i a t e &r For all customer enquiries or for replacement parts, contact:- ☎ 0870 609 1901 www.flymo.com customer.services@husqvarna.co.
Carton Contents Cable Management Lock-off button Electric Cable with moulded on plug Steady Handle (with bolt and nut) Hexagon Drive Tool Instruction Manual Cable Management Guard (with bolt and nut) IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
. Do not use the product if the electric cables are damaged or worn. 4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one. 5. Your extension cable must be uncoiled, coiled cables can overheat and reduce the efficiency of your product. 6. Keep the cable clear of the cutting area and obstacles at all times.
Assembly Instructions A B 3 1 4 1 2 2 3 C 3 2 D Steady Handle Assembly 1. Remove the Wing Knob (A1) and Bolt (A2) from the Steady Handle (A3). 2. Locate the Steady Handle (B1) onto the tube. Insert the Bolt (B2) through the Steady Handle and the Cable Management (B3) and secure with the Wing Knob (B4). 3. Adjust the Steady Handle to the most comfortable operating position by loosening the Wing Knob and moving the handle up or down the tube. 2 1 1 F E 1 1 2 Safety Guard Assembly 1.
Line Feed K The length of nylon line wears down naturally as you work. When this happens, tap the Cap (K1) on the ground while it is turning. A further length of line will automatically be fed out. The line cutter in the guard then ensures the line is cut to the optimum length. 1 AUTO IMPORTANT:- Too much line reduces motor speed and cutting performance. line cutter Use L • • 1 2 M • • • 1. 2. N 3. 4. 5. WARNING Wear eye protection.
Cutting Head To replace nylon line. For your convenience it is recommended you buy spool and line complete. Nylon line only is also available. Both are available from Husqvarna Outdoor Products stockists. To fit spool and line complete: 1. Remove the Cap (P1) and Spool Holder (P2) 2. Remove old spool.(Q) 3. Place new spool into spoolholder.(Q) 4. Release one line from cleat (T). 5. Secure line into eyelet (R1). 6. Repeat for second line. 7. Refit the Spoolholder and fit the Cap ensuring it is secure.
Maintenance V • WARNING Disconnect from the mains electricity supply, before attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your Product 1. Disconnect from the mains electricity supply. 2. Never clean your product with water, cleaning fluids, or solvents, just remove debris with a suitable tool, a soft brush or dry cloth. 3.
Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT LINE NOT FEEDING OR LINE TOO SHORT OR TRIMMER VIBRATES CONTINUOUS CLATTERING NOISE LINE SNAPS CONTINUOUSLY IF NONE OF THE ABOVE OR IF FAULT PERSISTS CHECK ACTION Remove cap and spool, free line and re-fit spool and cap.
EC Declaration of Conformity I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP. Certify that the product:Category........ Electric Lawn Trimmer Make.............. Husqvarna Outdoor Products Conforms to the specifications of Directive 2000/14/EC I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham.
