NetDAQ Users Manual
Table Of Contents
- 2640A/2645A NetDAQ Users Manual
- 1. Overview
- 2. Preparing for Operation
- Introduction
- Instrument Preparation
- Unpacking and Inspecting the Instrument
- Positioning and Rack Mounting
- Connecting to a Power Source and Grounding
- Universal Input Module Connections
- Digital I/O Connections
- Alarm/Trigger I/O Connections
- External Trigger Wiring for a Group Instrument
- Controls and Indicators
- Front Panel Operating Procedures
- Power-On Options
- Displaying a Monitor Channel
- Displaying the Digital I/O Status
- Displaying the Totalizer Status
- Reviewing and Setting the Base Channel Number
- Reviewing and Setting the Line Frequency
- Reviewing and Setting the Network Type
- Reviewing and Setting the General Network Socket Port
- Reviewing and Setting the General Network IP Address
- Reviewing and Setting the Subnet Mask and Default Gateway
- Viewing the Instrument Ethernet Address
- Host Computer and Network Preparation
- Testing and Troubleshooting
- 3. Configuring NetDAQ Logger for Windows
- Introduction
- Configuring Network Communications
- Configuring the Current Setup
- Setup Files
- Configuring an Instrument
- Configuring Channels
- Configuring Mx+B Scaling From a File
- Entering an Instrument's Description
- Copying a Channels Configuration
- Default Configuration Settings
- Using Configuration Lockout
- Saving an Instrument's Configuration as a Text File
- Configuring the netdaq.ini File
- 4. Operating NetDAQ Logger for
- 5. Using Trend Link for Fluke
- Introduction
- Getting the Right Look for Your Trend Link Chart
- 6. Maintenance
- Introduction
- Self-Test Diagnostics and Error Codes
- Cleaning
- Fuse Replacement
- Performance Test
- Configuring the Performance Test Setup
- Initializing the Performance Test Setup
- Accuracy Performance Tests
- Volts DC Accuracy Test (2640A)
- Volts DC Accuracy Test (2645A)
- Volts AC Accuracy Test
- Frequency Accuracy Test
- Analog Channel Integrity Test
- Computed Channel Integrity Test
- Thermocouple Temperature Accuracy Test
- Open Thermocouple Response Test
- 2-Wire Resistance Accuracy Test (2640A)
- 2-Wire Resistance Accuracy Test (2645A)
- 4-Wire Resistance Accuracy Test (2640A)
- 4-Wire Resistance Accuracy Test (2645A)
- RTD Temperature Accuracy Test (Resistance) (2640A)
- RTD Temperature Accuracy Test (Resistance) (2645A)
- RTD Temperature Accuracy Test (DIN/IEC 751 RTD)
- Digital Input/Output Tests
- Totalizer Tests
- Master Alarm Output Test
- Trigger Input Test
- Trigger Output Test
- Calibration
- Variations in the Display
- Service
- Replacement Parts
- Appendices
- A. Specifications
- Introduction
- 2640A/2645A Combined Specifications
- 2640A Specifications
- 2640A DC Voltage Measurement Specifications
- 2640A AC Voltage Measurement Specifications
- 2640A 4-Wire Resistance Measurement Specifications
- 2640A 2-Wire Resistance Measurement Specifications
- 2640A RTD's 4-Wire, per ITS-1990 Measurement Specifications
- 2640A RTD's 2-Wire per ITS-1990 Measurement Specifications
- 2640A Thermocouple per ITS-1990 Measurement Specifications
- 2640A Frequency Measurement Specifications
- 2645A Specifications
- 2645A DC Voltage Measurement Specifications
- 2645A AC Voltage Measurement Specifications
- 2645A 4-Wire Resistance Measurement Specifications
- 2645A 2-Wire Resistance Measurement Specifications
- 2645A 4-Wire RTD per ITS-1990 Measurement Specifications
- 2645A Thermocouple per ITS-1990 Measurement Specifications
- 2645A Frequency Measurement Specifications
- B. Noise, Shielding, and Crosstalk Considerations
- C. True-RMS Measurements
- D. RTD Linearization
- E. Computed Channel Equations
- F. Data File Format
- G. Dynamic Data Exchange (DDE)
- H. Ethernet Cabling
- I. Network Considerations
- J. Error Messages & Exception Conditions
- K. Fluke Service Centers
- A. Specifications
- Index
- Instrument Parameter Record (Isolated Network)
- Instrument Parameter Record (General Network)
- General Network Parameter Record
- Host Computer General Network Parameter Record
ix
List of Figures
Figure Title Page
1-1. 2640A/2645A NetDAQ Networked Data Acquisition Units.......................... 1-3
1-2. 2640A/2645A Front Panel .............................................................................. 1-4
1-3. Typical Front Panel Display During Scanning and Monitoring ..................... 1-5
1-4. 2640A/2645A Rear Panel................................................................................ 1-6
2-1. Instrument Preparation .................................................................................... 2-4
2-2. Connecting the Instrument to a Power Source................................................ 2-6
2-3. Universal Input Module Connections ............................................................. 2-9
2-4. 2-Wire and 4-Wire Connections..................................................................... 2-10
2-5. DIGITAL I/O Connector................................................................................. 2-12
2-6. ALARM/TRIGGER I/O Connector ................................................................ 2-14
2-7. External Trigger Wiring for a Group Instrument............................................ 2-16
2-8. Front Panel Controls........................................................................................ 2-17
2-9. Front Panel Indicators ..................................................................................... 2-18
2-10. Rear Panel Controls......................................................................................... 2-20
2-11. Rear Panel Indicators ...................................................................................... 2-20
2-12. Displaying a Monitor Channel........................................................................ 2-22
2-13. Examples During Monitor............................................................................... 2-23
2-14. Displaying the Digital I/O Status .................................................................... 2-24
2-15. Examples for Digital I/O and Totalizer Status................................................ 2-25
2-16. Displaying the Totalizer Status ....................................................................... 2-26
2-17. Reviewing and Setting the Base Channel Number ......................................... 2-27
2-18. Examples for Reviewing and Setting the BCN............................................... 2-28
2-19. Reviewing and Setting the Line Frequency .................................................... 2-29
2-20. Examples for Reviewing and Setting the Line Frequency.............................. 2-30
2-21. Reviewing and Setting the Isolated Network Type to Isolated....................... 2-31
2-22. Examples for Reviewing and Setting the Network Type................................ 2-32
2-23. Reviewing and Setting the Network Type to General..................................... 2-33
2-24. Examples for Reviewing and Setting General Network Parameters............... 2-34
2-25. Reviewing and Setting the General Network Socket Port .............................. 2-36
2-26. Reviewing and Setting the General Network IP Address ............................... 2-37
2-27. Reviewing and Setting the Subnet Mask and Default Gateway...................... 2-40