Datasheet

700PTPK Pneumatic
Test Kit
• Combine with any Fluke 700G
Series Gauge, 1,000 psi
(69 bar) or less, to make a com-
plete pressure testing kit
• Generate pressure up to
600 psi, 40 bar with the
700PTP-1 test pump
• Connect the 700G Series gauge
directly to the included PTP-1
hand pump
700HTPK Hydraulic
Test Kit
• Combine with any Fluke-700G
Series Gauge, 1,000 psi (69
bar) range or greater, to make a
complete pressure testing kit
• Generate pressure up to 10,000
psi, 690 bar with the included
700HTP-2 test pump
• Connect the 700G Series gauge
directly to the HTP-2 hand
pump
700LTP-1 Low Pressure
Test Pump
Hand operated pressure pump
designed to generate either
vacuum to -13 psi/-.90 bar or
pressures to 100 psi/6.9 bar. Ideal
for low pressure applications
requiring accurate low pressure
testing.
71XTrap Liquid and
Dirt Trap
The 71XTrap is designed to work
with pressure up to 500 psi and
mitigates the chance of fluid
damage in at-risk applications.
Designed to work with the 718
and 719PRO.
700ILF In-line Filter
The Fluke 700ILF can be used
to isolate the calibrator from
incidental contact with fluids.
Particularly useful with the 718
calibrator to help keep moisture
or oils from contaminating the on-
board pump.
700PTP-1 Pneumatic
Test Pump
The Fluke 700PTP is a handheld
pressure pump designed
to generate either vacuum to
-11.6 psi/-0.8 bar or pressure
to 600 psi/40 bar.
700HTP-2 Hydraulic
Test Pump
The Fluke 700HTP is designed
to generate pressures up to
10,000 psi/700 bar. Use the Fluke
700PRV adjustable relief valves to
limit pressures from 1360 psi to
5450 psi.
700HTH-1 Hydraulic Test
Hose
The 700HTH is a 10,000 psi,
700 bar test hose that connects to
a calibration unit under test from a
Fluke 700HTP hydraulic test pump.
700PMP Pressure Pump
The 700PMP is a hand-operated
pressure pump to provide pres-
sures up to 150 psi/1000 kPa.
Output fitting is 1/8 FNPT.
700-IV Current Shunt
• Conversion factor: 10 mV = 1mA
• Accuracy (% of input, one-year):
0.025 %
• Input current: 0 mA to 55 mA
• Input resistance: 250 Ω nominal
• Output resistance: 10 Ω nominal
• Accuracy specification applies
from +18 °C and 28 °C to 50 °C
• Maximum input voltage: 30 V dc
71X, Hose Kit
The Fluke 71X Hose Kit is a
compatible with the 717, 718 and
719pro calibrators 100 psi and
below.
The kit contains three translucent
hoses one meter long and one 1/8
to 1/4 NPT female-female adapter.
700PRV Pressure Relief
Valve Kit
The Fluke 700PRV consists of
two relief valves (1360 and 5450
psi) to be used with the 700HTP
Hydraulic Test Pump. These
relief valves will protect the most
commonly used Fluke pressure
modules from damage due to
accidental over-pressurization.
1/4 BSP male parallel thread to fit
Flu ke 70 0H T P.
For more information, go to www.fluke.com/accessories
51
Process tools