Datasheet

RS500 Probe Accessories
Replacement Set
For VPS510 Series Probes
• CAT II 300 V
• 1x hook clip (black)
• 1x ground lead with mini
alligator clip (black)
• 2x insulation sleeves for probe’s
ground contact (black)
• 1x BNC to probe tip adapter
(black)
• CAT II 30 V
• 2x ground browsers (black)
• 1x insulated mini screwdriver,
for probe adjustment purposes
i5s AC Current Clamp
• 0.01 A to 5 A
• Range 400 mV/A
• Basic accuracy % reading: 1 %
• Usable frequency range:
40 Hz to 5 kHz
TP920 Test Probe
Adapter Kit
Suited for STL120 Test Leads (Not
compatible with STL120-III), TL71
Test Leads, TL75 Test Leads and
TL76 Test Leads
The set consists of:
• IC test tip adapters for probing
closely spaced test points, such
as the pins of integrated cir-
cuits, without shorting adjacent
leads. Maximum current han-
dling 3A
• Extended probe tips allow test-
ing of hard to reach points.
Maximum current handling 3A
• Medium size alligator clips have
maximum jaw opening of 7.6
mm (0.30 in)
• Rated for 3 A max
TAS 90 Shielded Test lead
Accessory Set
• Set 4 mm adapters for Banana
plug (1x red, 1x grey, 2x black)
• Set of back probe pins for
Banana plug (1x red, 1x grey, 2x
black)
• CAT II 30 V
• Rated for 1A max
PM9091 Set of 3x Coaxial
Cables with BNC connec-
tors
• Length: 1.5m each
• Impedance: 50 ohm
• Color: 1xRed, 1xBlack, 1x3x
Grey
• Max signal voltage: 300 V rms
• Max voltage to ground:
600 V rms CAT III per IEC/
EN61010-031
PM9092 Set of Coaxial
cables with BNC connec-
tors
• Length: 0.5 m each
• Impedance: 50 ohm
• Color: 1x red, 1x black, 1x grey
• Max signal voltage: 300 V rms
• Max voltage to ground:
600 V rms CAT III per IEC/
EN61010-031
PM9093 Adapter BNC
(male) to Dual BNC (female)
in T model (6)
• Color: 2x black
• Max signal voltage: 300 V rms
CAT III per IEC/EN61010
• Max voltage to ground: 600V
rms CAT III per IEC/EN61010
PM9081 Adapter BNC
(female) to Dual Banana
Jack
• Color: 2x red, 2x black
• Max signal voltage: 600Vrms
CAT III per IEC/EN61010
• Max voltage to ground: CAT III
600 Vrms / CAT II 1000 V per
IEC/EN61010
PM9082 Adapter BNC
(male) to Dual Banana Jack
• Color: 2x red, 2x black
• Max signal voltage: CAT III
600 Vrms per IEC/EN61010
• Max voltage to ground: CAT III
600Vrms /CAT II 1000V per
IEC/EN61010
BB120 Adapter BNC
(female) to Shielded
Banana Jack
• Set of 2
• Max signal voltage: 300 Vrms
CAT III per IEC/EN61010
• Max voltage to ground: 600 V
CAT III per IEC/EN61010
TRM50 Coaxial Feed-
through BNC male to BNC
female Cable Terminator
• Set of 2
• Specification
• Impedance: 50 ohm
• Max voltage over ground:
CAT III 1000 V
• Max power 1W
BHT190 Bus Health Test
Break-out Adapter Set
• Board with M12 connectors
(male to female, 5 pins)
• DB-9 connectors (male to
female, 9 pins + shield)
• RJ-45 connector, with short
patch cable providing male to
female interconnection (8 pins)
CS20MA Current Shunt for
AC and DC measurements
on 4 to 20mA control loops
• Sensitivity: 10mV/mA
• Shunt resistance: 10 ohm
• Bandwidth: > 10 kHz
• Max voltage to ground: CAT III
30 Vrms per EN/IEC 61010
MA190 Medical Applica-
tions Accessory Kit
• 1x 50 ohm BNC feed through
terminator
• 1x 50 ohm BNC feed through
terminator with 10:1 signal
attenuator
• 1x 1 ohm current shunt in BNC
feed through
• 1x BNC terminated coax cable
• 1x Single piece insulated BNC
(female) to 4mm Banana plug
adapter
• 2x Pieces dual 4mm Banana
receptacles (1x red, 1x black)
EBC290 External Charger
For Fluke 190 Series II
ScopeMeter
®
Oscilloscope
• Charging time (BP291): five
hours, giving an operating time
of up to seven hours
• DC input voltage: 15 V to 23V,
714 mA nom. (dc input from
BC190: 17.8 V / 0.84 A max)
For more information, go to www.fluke.com/accessories
41
Portable oscilloscopes