Datasheet

TLK281 SureGrip
™
Automotive Test Lead Kit
This complete set of test and
measurement accessories is
designed for automotive special-
ists. Sharp stainless steel probes
can be used to contact the wire
conductor or pinpoint tests on a
circuit or relay while the large-
jaw alligator clips ensure a good
ground on the engine or connec-
tion to battery terminals. Also
includes silicone-insulated test
leads and a convenient case.
Rated to 60V dc. Kit includes:
• TP81 Insulation Piercing
Clip Set
• TL224 SureGrip™ Insulated Test
Leads
• TP220 SureGrip™ Industrial
Test Probes
• AC220 SureGrip™ Alligator Clips
• AC285 SureGrip™ Alligator Clips
• Soft case
TLK282 SureGrip
™
Deluxe
Automotive Test Lead Kit
This kit includes everything in
the TLK281 Kit plus a few extras.
The back probe pins slide past
weather-pack connectors on fuel
injectors, TPS, and MAP sensors.
A hook probe with plunger actua-
tion allows quick connection to
pins or exposed conductors.
Kit includes:
• TP81 Insulation Piercing
Clip Set
• TP40 Automotive Back Probe
Pins (five)
• TL224 SureGrip™ Insulated Test
Leads
• TP220 SureGrip™ Industrial
Test Probes
• AC220 SureGrip™ Alligator Clips
• AC285 SureGrip™ Alligator Clips
• AC280 SureGrip™ Hook Clips
• Soft case
• Rated to 60 V dc
TP40 Automotive
Back Probe Pins
Flexible and formable 31.75 mm
(1.25 in) pins provide an easy
connection past weather-pack
seals to connector conductors.
These five pins are a must-have
for fuel injectors, TPS, and MAP
sensors, as well as for any under-
hood or under-vehicle connector
with weather-pack seals.
• 4 mm (0.16 in) banana jack
accepts digital multimeter and
banana jack leads
• Easily connects to modular
leads such as the TL224
• Rated to 60 V dc
TP81/TP82 Insulation
Piercing Clip Set
Two stainless steel probes (red,
black) pierce insulation on 14, 16
and 18 gauge wire. Needle depth
can be controlled to minimize
insulation damage. Essential for
use under hood or under dash.
Can be used on fuel injectors or
sensors while providing complete
insulation to grounding. Probe
connects to a banana jack that
accepts all digital multimeter and
banana jack leads (such as the
TL224 SureGrip™ Insulated Test
Leads).
• TP81 has non-rotating
4 mm (0.16 in) banana jack to
prevent leads from tangling
• Rated to 60 V dc
• TP82 is for use with test leads
with 2 mm probes
TP88 Rigid Back
Probe Pins
Better than a test probe alone,
these rigid back probe pins easily
pass between a weather-pack
seal and wire. A sharp point
ensures good contact to the elec-
trical connector, and insulation
protects the pin from shorting to
other wires.
• Slides onto 2 mm (0.08 in) test
probes
• Probe length: 51 mm (2 in)
• Rated to 60 V dc
RPM80 Inductive
Pick-Up/External Trigger
• Provides RPM measurement
capability when clipped on
spark plug wire
• For use with Fluke 88 Series
and 78 Series DMMs
TP88
RPM80
45
For more information, go to www.fluke.com/auto-accy
TL82
Automotive