Datasheet

ManualsBrandsFLUKE ManualsLaboratory Test Equipment-MDA-550 Motor drive analyzer 500 MHz

TECHNICAL DATA

Fluke MDA-510 and MDA-550

Motor Drive Analyzer

Simplify complex motor-drive troubleshooting

with guided test setups and automated drive

measurements that provide reliable, repeatable test

results.

The new Fluke MDA 510 and MDA 550 Motor-Drive Analyzers save

time and eliminate the hassle of setting up complex measurements,

while simplifying the troubleshooting process. Simply select a test

and the step-by-step guided measurements show you where to

make voltage and current connections, while the preset measure-

ment profiles ensure you will capture all the data you need for each

critical motor-drive section—from the input to the output, the DC

bus, and the motor itself. From basic to advanced measurements,

the MDA-500 Series has you covered, and with a built-in report

generator you can quickly and easily generate as-found, and as-left

reports with confidence.

The MDA-510 and MDA-550 are the ideal portable motor-drive

analysis test tools, and can help safely locate and troubleshoot

typical problems on inverter type motor-drive systems.

• Measure key motor-drive parameters including voltage, cur-

rent, DC Bus voltage level and AC ripple, voltage and current

unbalance and harmonics (MDA-550), voltage modulation, and

motor shaft voltage discharges (MDA-550).

• Perform extended harmonics measurements to identify the

effects of low and high order harmonics on your electrical power

system.

• Conduct guided measurements for motor-drive input, DC bus,

drive output, motor input and shaft measurements (MDA-550)

with graphical step-by-step voltage and current connection

diagrams.

• Use simplified measurement setup with preset measurement

profiles to automatically trigger data collection based on the

chosen test procedure.

• Create reports quickly and easily that are perfect for docu-

menting troubleshooting and collaborative work with others.

• Measure additional electrical parameters with full 500 MHz

oscilloscope, meter and recording capability for complete range

of electrical and electronic measurement on industrial systems.

KEY MEASUREMENTS

Inverter output voltage, DC bus voltage and

ripple voltage, harmonics, unbalance

THREE POWERFUL TEST TOOLS IN

ONE

Motor-drive analyzer, waveform analyzer

and recording data logger all in one

HIGHEST SAFETY RATING IN THE

INDUSTRY

600 V CAT IV/1000 V CAT III rated for use at

the service entrance and downstream

Summary of content (10 pages)

PAGE 1
TECHNICAL DATA Fluke MDA-510 and MDA-550 Motor Drive Analyzer Simplify complex motor-drive troubleshooting with guided test setups and automated drive measurements that provide reliable, repeatable test results. The new Fluke MDA 510 and MDA 550 Motor-Drive Analyzers save time and eliminate the hassle of setting up complex measurements, while simplifying the troubleshooting process.
PAGE 2
The Fluke MDA-510 and MDA-550 Motor Drive Analyzers use guided test measurements to make analysis easier than ever Drive input Measure input voltage and current to quickly see whether values are within acceptable limits by comparing the drive’s nominal rated voltage to the actual supplied voltage. Then, check the input current to determine if the current is within the maximum rating and the conductors are suitably sized.
PAGE 3
Voltage modulation Measurements of the Pulse Width Modulated signal are used to check for high voltage peaks which can damage motor winding insulation. The rise time or steepness of impulses is indicated by the dV/dt reading (rate of voltage change over time), this should be compared to the motor’s specified insulation.
PAGE 4
Quick and easy measurement setup 1) Press ‘Motor Drive Analyzer’ button and select ‘Drive Measurement Location’. 4) Select the measurement method/option. 2) Use the on-screen context information to further guide you to successful setup and measurement. 5) Connect the test probes according to the diagram. Once complete press ‘Next’. 3) Choose the measurement. 6) The analyzer will then automatically trigger, and configure the reading for the optimum measurements.
PAGE 5
Reporting and analysis The MDA-500 Series simplifies the process of gathering data and writing test reports with a built-in report generator. At each test point or measurement there is the option to create, update or modify a report. Simply press ‘SAVE TO REPORT’ and select the appropriate screens to save into a text based report file. By performing the step-by-step guided measurements a comprehensive report can be created directly from the instrument to document the entire troubleshooting process.
PAGE 6
Featured measurements Measurement and Analysis Combinations Test point Sub group Reading 1 Reading 2 Reading 3 Reading 4 V-A-Hz V ac+dc A ac+dc Hz V peak V peak max V peak min V pk-to-pk Crest factor A peak A peak max A peak min A pk-to-pk Crest factor V-A-Hz V ac+dc A ac+dc Hz V peak V peak max V peak min V pk-to-pk Crest factor A peak A peak max A peak min A pk-to-pk Crest factor Unbalance V ac+dc V ac+dc V ac+dc Unbalance Peak V pk-to-pk V pk-to-pk V pk-to-pk Un
PAGE 7
Phase-DC - Zoom 1 V PWM V pk-to-pk V peak max V peak min Zoom 2 V peak max V peak min Delta V Hz Zoom 3 peak V peak max Delta V/s Risetime peak Overshoot Zoom 3 level Delta V Delta V/s Risetime level Overshoot V-A-Hz V PWM A ac+dc Hz V/Hz V peak V peak max V peak min V pk-to-pk Crest factor A peak A peak max A peak min A pk-to-pk Crest factor Unbalance V PWM V PWM V PWM Unbalance Peak V pk-to-pk V pk-to-pk V pk-to-pk Unbalance A ac+dc A ac+dc A ac+dc Peak A
PAGE 8
Specifications Measurement Function Specification DC voltage (V dc) Maximum voltage with 10:1 or 100:1 probe 1000 V Maximum resolution with 10:1 or 100:1 probe 1 mV Full scale reading 999 counts Accuracy at 4 s to 10 us/div ± (3 % + 6 counts) AC voltage (V ac) Maximum voltage with 10:1 or 100:1 probe 1000 V Maximum resolution with 10:1 or 100:1 probe 1 mV Full scale reading 999 counts 50 Hz ± (3 % + 10 counts) - 0.6 % 60 Hz ± (3 % + 10 counts) - 0.
PAGE 9
Current (AMP) with current clamp Ranges Same as V ac, Vac+dc or V peak Scale Factors 0.1 mV/A, 1 mV/A, 10 mV/A, 20 mV/A, 50mV/A, 100 mV/A, 200 mV/A, 400 mV/A Accuracy Same as Vac, Vac+dc or V peak (add current clamp accuracy) Frequency (Hz) Range 1.000 Hz to 500 MHz Full scale reading 999 counts Accuracy ± (0.
PAGE 10
Ordering information MDA-510 Motor drive analyzer, 4 channel, 500 MHz MDA-550 Motor drive analyzer, 4 channel, 500 MHz with motor shaft and harmonics Includes 1x BP 291 li-ion battery pack, 1x BC190 charger/power adapter, 3x VPS 100:1 high voltage probes with alligator clips, 1x VPS410-II-R 10:1 500MHz voltage probe, 1x i400s ac current clamp, 1x C1740 carrying case, 1x 2 GB USB drive with manuals and FlukeView™ 2 software MDA-550 also includes 1x SVS-500 shaft voltage set (3x brush, probe holder, two-piece