Data Sheet
3 Fluke Corporation Fluke 750P Series Pressure Modules
Image Description Application
Fluke 700PTP-1 Pneumatic Test Pump
The Fluke 700PTP-1 is a handheld pressure
pump designed to generate either vacuum
to -13 psi/-0.9 bar or pressure to
600 psi/40 bar
The Fluke 700PTP-1 has two pressure ports:
• ¼” NPT female parallel thread fitting for
the reference gauge or pressure module
• ¼” NPT female parallel thread fitting for
the unit under test
The Fluke 700PTP-1 features an integral pressure adjustment vernier
which varies the pressurized volume by 2.0 cc over approximately
eleven turns of the vernier knob. The pressure variation achievable with
the vernier will depend on the nominal pressure and total pressurized
volume, but with a minimum volume and maximum pressure, the vernier
provided 600 ± 20 psi adjustment range. With a minimum volume and
no pressure applied, the vernier can also be used to provide a 0 to 70˝
H2O range. Larger volumes will provide a smaller range of adjustment,
but greater resolution. The length of the stroke can be adjusted to limit
the maximum output pressure. Maximum output pressure is adjustable
from 2.5 psi to 600 psi.
For use with: Fluke 700 and 750P Series Pressure Modules and the
Fluke 710 and 720 Series Pressure Calibrators
Fluke 700HTP-2 Hydraulic Test Pump
The Fluke 700HTP-1 is designed to generate
pressures up to 10000 psi/700 bar. The
Fluke 700HTP-1 has two pressure ports:
• ¼” NPT female parallel thread fitting for
the reference gauge or pressure module
• ¼” NPT female parallel thread fitting for
the unit under test
Note: The user must provide a hose with appropriate end
fittings from this port to the unit under test.
This pump can provide up to 10000 psi using distilled water or mineral-
based hydraulic oil. The pump is operated by pumping several strokes
to prime the system, then switching to high pressure mode when the
resistance increases. An integral pressure adjustment vernier knob varies
the pressurized volume by 0.6 cc. The pressure variation achievable with
the vernier will depend on the nominal pressure and total pressurized
volume, but with a minimum volume, the vernier provided 150 psi to
3000 psi (at 150 psi nominal) and 3000 psi to 10000 psi (at 3000 psi
nominal) adjustment ranges. With a minimum volume and no pressure
applied, the vernier can also be used to provide a 0 to 1.7 psi range.
Larger volumes will provide a smaller range of adjustment, but greater
resolution.
For use with: Fluke 700 and 750P Series Pressure Modules and the
Fluke 710 and 720 Series Pressure Calibrators
Fluke 700LTP-1 Low-Pressure Test Pump
The Fluke 700LTP-1 is a hand operated
pressure pump designed to generate either
vacuum to -12 psi/-.85 bar or pressures to
100 psi/6.9 bar. The Fluke 700LTP-1 has
two pressure ports with push fit connec-
tors. These push fit connectors, one for the
reference port for connection to a Fluke 700
Series Pressure Module and one to connect
to a unit under test, connect to the supplied
test hoses.
The Fluke 700LTP-1 is primarily intended for low pressure applications.
It features a fine adjust vernier with .00145 psi resolution at low pres-
sures. The pressure variation achievable with the vernier will depend on
the nominal pressure and total pressurized volume, but with minimum
volume and maximum pressure the vernier provides 30 psi ± 6 psi. The
adjustable pressure relief valve features a slow-bleed capability that
allows the user to slowly release pressure at a controlled rate to achieve
a desired pressure.
Fluke 700HTH-1 Hydraulic Test Hose
The Fluke 700HTH-1 Hydraulic Test Hose
is a 10000 psi, 700 bar working pressure
test hose. The hose uses self-sealing fittings
with easy finger tight connections.
The Fluke 700HTH-1 allows connections to a unit under test from a
Fluke 700HTP-1 hydraulic test pump in use with the Fluke 700 and
750P Series Pressure Modules. The 700HTH-1 is compatible with water
and non-corrosive oil.
Fluke 71X Hose Kit
The Fluke 71X hose kit includes (2) quick
disconnect fittings to connect to the 718 or
719, (3) 1-meter translucent hoses and one
BSP adapter.
For use with: Fluke 718 and 719 Pressure Calibrators
Fluke 700PRV-1 Pressure Relief Valve Kit
The Fluke 700PRV-1 consists of two relief
valves (1360 and 5450 psi) to be used with
the 700HTP-1 Hydraulic Test Pump. These
relief valves will protect the Fluke pressure
modules from damage due to over-pressur-
ization. 1/4 BSP male parallel thread to fit
Fluke 700HTP-1.
Repeatability ± 10 % of nominal setting. Multiturn adjustment screw to
set preload on internal disc springs.
For use with: Fluke 700HTP-1 Hydraulic Test Pump.
Fluke 700 PMP Pressure Pump
The Fluke 700PMP is a hand-operated pres-
sure pump to provide pressures up to
150 psi/1000 kPa. Output fitting is 1/8
FNPT.
Linear stroke of 1.6 in (4 cm). Multi-turn vernier for fine adjustment of
pressure. Includes controlled pressure bleed valve.
For use with: Fluke 700 and 750P Series Pressure Modules and the
Fluke 710 and 720 Series Pressure Calibrators.
Pressure accessories