TS 22 Series Craft Test Sets Users Guide PN 2451689 October 2005 Rev. 2 6/2015 ©2005, 2010, 2015 Fluke Corporation All product names are trademarks of their respective companies.
LIMITED WARRANTY AND LIMITATION OF LIABILITY Each Fluke Networks product is warranted to be free from defects in material and workmanship under normal use and service unless stated otherwise herein. The warranty period for the mainframe is 18 months and begins on the date of purchase. Parts, accessories, product repairs and services are warranted for 90 days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are all considered parts or accessories.
Table of Contents Title Page Introduction ...................................................................................................................................................... 1 Registration ....................................................................................................................................................... 1 Contacting Fluke Networks .........................................................................................................................
TS22 Series Craft Test Sets Users Guide ii
® TS 22 Series Craft Test Sets Introduction Warning Good safety practices prohibit the connection of the TS22 Series and similar test sets to 117 volts ac commercial electrical power. Should the TS22 Test Set be connected to commercial power, all warranties are immediately voided. Contacting Fluke Networks www.flukenetworks.com support@flukenetworks.
TS22 Series Craft Test Sets Users Guide Safety Information Physical Characteristics The following IEC symbols are used either on the test set or in the manual: Housing Warning: Risk of personal injury. See the manual for details. Warning: Risk of electric shock. The housing for the TS22 Series Test Set is made of high-impact polycarbonate which provides excellent insulating properties.
Physical Characteristics FS H POL L NR E T ON PULS E bfs01.eps Figure 1. Physical Characteristics Battery See Figure 1. Warning When not in use, the 9 V battery in the TS22 Series Test Set should be changed once a year to prevent the 3 V lithium battery from draining. When the 9 V battery is low your speakerphone will no longer work. You should replace the 9 V battery with a new battery immediately so as to not drain the 3 V lithium battery.
TS22 Series Craft Test Sets Users Guide bfs02.eps Standard Line Cord (STD) with Piercing Pin Clips: This cord consists of one red and one black conductor, each approximately five feet long. Each conductor has an alligator clip offset 20° to minimize clip shorting. The clips have insulation piercing spikes and a neoprene boot.
Physical Characteristics bfs03.eps Talk/ Monitor Switch The T (TALK), position establishes an off-hook condition for dialing and talking as a common battery telephone. The M (MONITOR) position removes the transmitter from the circuit, and provides a high impedance coupling. On the TS22A, the M position provides a high impedance coupling, which allows line monitoring without disrupting conversations or signaling.
TS22 Series Craft Test Sets Users Guide Keypad Controls and Indicators Figure 4 describes the keys, controls, and indicators in the keypad area of the TS22 test sets. bfs04.eps Numeric Keypad The numeric keypad is used to dial telephone numbers and make function selections. The numeric keypad includes 12 standard dialing keys including the star ( ) and the pound (#) keys. The four special purpose keys are labeled STO, RCL, LNR, and PSE.
Operation Operation TS22A Speaker Monitor Mode To put the TS22A Test Set into speaker monitor mode: TS22 Amplified Speaker Mode 1 Set the TALK/MONITOR switch to M, then press the SPEAKER button once to enter speaker mode with low volume. To put the TS22 Test Set into amplified speaker mode: 1 Connect the test set to a line. The TALK/MONITOR switch may be in either position. 2 Press the SPEAKER button a second and third time for medium and high volume.
TS22 Series Craft Test Sets Users Guide Storing Number in Repertory Memory (Auto Dialer) The TS22 and TS22A Test Sets have 9 memory locations, which correspond to number keys 1 through 9. Each location will store up to 18 digits. If a nineteenth digit is entered, the previous digits will be cleared and the last digit (the nineteenth entered) starts a new string. If more than 18 digits are required, a second memory can be used.
Maintenance Line Monitoring Caution When testing circuits which are relatively close to the battery source, the clicks may be loud enough to cause acoustical shock if the receiver is held tightly against the ear. The TS22 Series Test Sets are designed to rest comfortably on the shoulder with the receiver away from the ear. They should be used in this position when listening for clicks. Set the TALK/MONITOR switch to M and connect test leads to circuit under test.
TS22 Series Craft Test Sets Users Guide Replacing the Belt Clip Note Be sure to replace the battery with a good 9 V battery or the test set will not operate at all. See Figure 6. To replace the battery (see Figure 5): 1 Disconnect the test set from the line and place on a flat work surface with battery cover up. 2 Using a Phillips screwdriver, remove the three screws from the battery compartment. The belt clip assembly is field replaceable in the event of damage or prolonged wear.
Specifications Specifications Measurement Electrical Loop Limit Physical 2 k maximum at 48 VDC (nominal 20 mA minimum loop current) DC Resistance (Talk Mode) 300 typical Maximum voltage 300 V with transient protection to 1500 Vpk 10.25 in x 2.69 in x 3.38 in (26 cm x 6.83 cm x 8.57 cm) Weight TS22 21 ounces (.595 kg) TS22A 22 ounces (.
TS22 Series Craft Test Sets Users Guide 12
