Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
• Show the exact physical positions of all static Fluidmesh
components and approximate physical positions of all mobile
Fluidmesh components, against the background of an aerial map.
Plotting and interpreting static and mobile device information
To plot and interpret information on all static and mobile wireless devices
shown by the window, do the following steps:
1. Click the -Fluidity Quadro link under NETWORK CONTROL in
the left-hand settings menu.
NOTE
The Fluidity Quadro window needs Adobe Flash
Player to function. If your browser does not have the
Flash Player plug-in installed, you will be prompted to
download and install the plug-in.
• A graphical view of the current network will be shown. A
typical example is shown in (Figure 38 (page 90)).
Figure 38. Fluidity Quadro graphical view
2. Within the Fluidity Quadro graphical view:
• Static-mount Fluidmesh radio transceiver devices are
shown as centralized dots. Mesh End devices are shown
as blue dots, while Mesh Point devices are shown as red
dots. If an abnormal condition is detected on any static
unit, its device icon changes to a yellow dot.
• If a mobile radio transceiver device is within range of a
static device, and a data connection is established
between the devices, the mobile device is shown as a
colored border around the dot representing the static
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 90 of 180