Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
6. DEVICE CONFIGURATION USING THE
CONFIGURATOR INTERFACE
Fluidmesh radio devices that are capable of operating as part of a mesh
network, including each Fluidmesh 4200 FIBER, are shipped from the
factory in Mesh Point mode.
All Fluidmesh radio transceiver devices are shipped with IP address
192.168.0.10, and Netmask 255.255.255.0.
The Fluidmesh 4200 FIBER can be configured by using:
• The RACER™ Radio Configuration interface, or
• The on-board Configurator interface.
The difference between these interfaces is as follows:
RACER is a centralized, internet-based configuration software platform
that is accessed from the Fluidmesh Partner Portal.
• An internet connection must be made between the Fluidmesh
device and the RACER Cloud Server (an internet-based radio
management service).
• Devices can be configured on an Online basis only: configuration
settings are applied to one or more devices without the need for a
configuration (*.CONF) file, and manual configuration is disabled.
• If devices must be configured on an Offline basis (in other words, if
the device is not connected to the internet, and therefore cannot
access its configuration settings from the RACER Cloud Server), a
separate configuration file can be uploaded to the device using the
Configurator (described below).
The Configurator is a localized configuration software platform that
resides on the Fluidmesh device.
• Local configuration is done by connecting a computer to the device
through a direct hardware connection, or through the internet.
• Using the Configurator, devices can be configured on an Offline
basis only. A configuration (*.CONF) file can be manually applied to
set the device parameters, or each device parameter can be
manually set by the device user.
• Offline configuration settings for more than one Fluidmesh device
type can be integrated into a single configuration file. When the
configuration file is uploaded to each device, the device
automatically loads the correct configuration settings for its device
type.
To configure the unit using RACER, refer to the Fluidmesh Networks
RACER User Manual.
To configure the unit using the Configurator, refer to the following sub-
sections.
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 50 of 180