Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
Connecting fiber-optic connectors to SFP modules
Fiber-optic components are extremely sensitive to water, dirt and dust. In
particular, the optical interfaces of these components must not be
contaminated by foreign matter under any circumstances.
Ensure optimal performance of a fiber-optic network by connecting fiber-
optic connectors to XCO-type SFP modules only as shown below:
1. Do not remove protective covers from any fiber-optic components
until you are ready to connect and seal the components within a
minimal period of time.
2. Remove the protective cap covering the connection ports of the
SFP module.
3. Slide the round threaded tube that covers the SFP port connector
back along the fiber-optic cable, until the port connector is fully
exposed (below). Note the locking lugs on the metal port
connector.
4. Remove the dust covers from the SFP module.
5. Move the metal port connector (1, below) fully forward until the
locking lugs snap into the SFP port (2, below).
CAUTION
Do not attempt to connect the duplex fiber-optic cable
connector to the SFP module until the metal port
connector is fully engaged with the SFP port.
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 34 of 180