Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
undertakings (including obtaining any necessary export license or other
governmental approval), prior to operating the Fluidmesh Devices and
Fluidmesh Firmware, or exporting, re-exporting, releasing or otherwise
making the Fluidmesh Devices and Fluidmesh Firmware available outside
the U.S. You acknowledge and agree that Fluidmesh has no further
responsibility after the initial delivery to you, and you hereby agree to
indemnify and hold Fluidmesh harmless from and against all claim, loss,
liability or damage suffered or incurred by Fluidmesh resulting from, or
related to your failure to comply with all export or import regulations.
13.14. General
This Agreement shall not be governed by the 1980 U.N. Convention on
Contracts for the International Sale of Goods. Rather, this Agreement
shall be governed by the laws of the State of Illinois, including its Uniform
Commercial Code, without reference to conflicts of laws principles. You
agree to the exclusive jurisdiction and venue of the State and Federal
courts in Illinois, United States.
This Agreement is the entire agreement between you and Fluidmesh, and
supersedes any other communications or advertising with respect to the
Fluidmesh Firmware and accompanying documentation. If any provision
of this Agreement is held invalid or unenforceable, such provision shall be
revised to the extent necessary to cure the invalidity or unenforceability,
and the remainder of the Agreement shall continue in full force and effect.
This Agreement and all documents, notices, evidence, reports, opinions
and other documents given or to be given under this Agreement
(collectively with this Agreement, 'Documents') are and will be written in
the English language only. In the event of any inconsistency between any
Document in the English language and any translation of it into another
language, the English-language Document shall prevail. If you are
acquiring the Fluidmesh Firmware on behalf of any part of the U.S.
Government, the following provisions apply: The Fluidmesh Firmware and
accompanying documentation are deemed to be 'commercial computer
software' and 'commercial computer software documentation',
respectively, pursuant to DFAR Section 227.7202 and FAR 12.212(b), as
applicable. Any use, modification, reproduction, release, performance,
display or disclosure of the Fluidmesh Firmware and/or the accompanying
documentation by the U.S. Government or any of its agencies shall be
governed solely by the terms of this Agreement and shall be prohibited
except to the extent expressly permitted by the terms of this Agreement.
Any technical data provided that is not covered by the above provisions is
deemed to be 'technical data-commercial items' pursuant to DFAR
Section 227.7015(a). Any use, modification, reproduction, release,
performance, display or disclosure of such technical data shall be
governed by the terms of DFAR Section 227.7015(b).
Fluidmesh is a trademark of Fluidmesh, LLC in the United States and
worldwide.
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 179 of 180