Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
information. In no event shall Fluidmesh Networks LLC be held liable for
any incidental, consequential or special damages, whether based on tort,
contract or otherwise, arising out of or in connection with this manual, the
software or other information contained herein, or use thereof.
Fluidmesh Networks LLC, reserves the right to make any modification to
this manual or the information contained herein at any time, without
notice. The software described herein may also be governed by the terms
of a separate end-user license agreement.
Fluidmesh is a registered trademark of Fluidmesh Networks LLC.
MeshWizard, EasyMesh, FMQuadro, FluidThrottle, VOLO, Fluidity, Virtual
Gig, ENDO and MOBI are trademarks of Fluidmesh Networks LLC.
Microsoft, Windows, Internet Explorer and Microsoft Edge are registered
trademarks of the Microsoft Corporation in the United States and/or other
countries.
Ethernet is a registered trademark of the Xerox Corporation.
Adobe and Flash Player are registered trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
All other brands and product names that appear in this manual may be
trademarks or registered trademarks. Such brands and product names
are the property of their respective owners.
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 172 of 180