Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
(1) l'appareil ne doit pas produire de brouillage, et, and (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioelectrique subi, meme si le
brouillage est susceptible d'en compromettre le fonctionnement.
IC RF Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 21cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements
IC établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 21 cm de distance entre la source
de rayonnement et votre corps.
EC Declaration of Conformity
Fluidmesh Networks, Inc. declares under its sole responsibility that
the Fluidmesh 4200 FIBER is compliant with the following directives, and
has been designed and manufactured to the following specifications:
EMC EN 61000-6-1; EN 61000-6-2; EN 61000-6-3; EN 61000-6-4;
EN 489-17
R&TTE EN 300 328-1 V. 1.3.1; EN 300 328-2 V. 1.2.1; EN
301 893-1 V. 1.2.1; EN 300 440-2 V. 1.3.1
Safety EN 60950-1:2001
Caution: This equipment is intended to be used in all EU and EFTA
countries. Contact local Authority for procedure to follow.
Note:
Class A ITE is a category of all other ITE which satisfies the class A ITE
but not the class B ITE limits.
Such equipment should not be restricted in its sale but the following
warning shall be included in the instruction for use:
WARNING: this is a class A product. In a domestic environment, this
product may cause radio interference in which case the user may be
required to take adequate measures.
For more details on legal combinations of power levels and antennas,
contact Fluidmesh Networks, Inc.
Belgique
Dans le cas d’une utilisation privee, `a l’exterieur d’un batiment, au-
dessus d’un espace public, aucun enregistrement n’est necessaire pour
une dis-tance de moins de 300m. Pour une distance sup´erieure `a 300m
un enregistrement aupr`es de l’IBPT est requise. Pour une utilisation
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 169 of 180