Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
7.2.5. Sharing License codes and accepting shared License codes
If needed, you can share license codes with other Fluidmesh device
users, and also have other Fluidmesh device users share their license
codes with you.
To share one or more license codes with another Fluidmesh device user,
do the steps that follow:
1. Log on to the Fluidmesh Partner Portal.
2. Click the Plug-ins link.
• The Plug-ins web page will be shown.
3. Check the selection check-boxes to the left of the plug-ins that
must be shared.
4. Click the Share button in the upper left-hand corner of the Plug-
ins web page (Figure 88 (page 162)).
Figure 88. Plug-ins web page (Share button)
• The Share License Codes dialog will be shown.
5. Enter one or more E-mail addresses to which the License codes
must be sent. Click the Share button.
• An E-mail containing the selected License codes will be
sent to the specified E-mail addresses.
• The License codes contained in the E-mail can be
converted to plug-in Activation codes in the normal way.
If needed, you can also ask another device user to share one or more
license codes with you. If a License code is shared with you, it will be
listed on your Partner Portal Plug-ins web page.
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 162 of 180