Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
Plugin FM 3200
BASE
FM 3200
ENDO
FM 3500
ENDO
FM 4200
FIBER
FM 4200
MOBI
FM 4500
FIBER
FM 4500
MOBI
FM 4800
Fluidmesh
Access
Points
Available Not
available
Available Not
available
Not
available
VLAN Available Available Available Available Available
Virtual
Gigabit
Not
available
Not
available
Not
available
Not
available
Not
available
L2TP Available Available Available Available Available
PROFINET Available Available Available Available Available
QNET Available Available Available Available Available
FIPS Available Available Available Available Available
TITAN Available Available Available Available Available
UNII2 Available Available Available Available Available
To purchase any of the software plug-ins, please contact your Fluidmesh
Networks representative.
7.2. Plug-in management procedures
7.2.1. Plug-in activation
The Plug-in management procedure has been standardized, and is the
same for all Fluidmesh hardware devices.
To obtain a plug-in activation code for a Fluidmesh device, do the
following steps:
1. Contact your Fluidmesh Networks representative to purchase a
generic 16-digit License code for plug-in activation.
2. Quote the unique mesh unit identification number (5.a.b.c) of the
Fluidmesh hardware device.
3. Using the Fluidmesh Partner Portal, associate the License code
with the quoted Fluidmesh device to get an Activation code.
4. Enter the Activation code on the MANAGE PLUG-INS window for
the unit.
You can also deactivate a plug-in Activation code that is currently in use
so it can be used with a different Fluidmesh unit. To deactivate an active
plug-in, refer to The PLUGINS sub-tab.
To convert a License code into an Activation code for a Fluidmesh device,
do the following steps:
1. Log on to the Fluidmesh Partner Portal.
2. Click the Plug-ins link.
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 155 of 180