Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
Plug-in Is the plug-
in package
removable
and re-
installable?
Function Part number
PROFINET Yes Enables process field net
capability.
FM-PROFINET
QNET Yes Enables Neutrino Qnet
capability.
FM-QNET
FIPS Yes Enables Federal Information
Processing Standards
capability.
FM-FIPS
TITAN Yes Enables fast fail-over
capability on networks where
redundant (backup) units are
installed.
FM-TITAN
UNII2 No Enables use of frequencies in
the Unlicensed National
Information Infrastructure (U-
NII) bands.
Supported bands are U-
NII-2A (5.250 to 5.350 GHz)
and U-NII-2C / U-NII-2E
(5.470 to 5.725 GHz).
FM-UNII2
The following tables describe which plug-ins are compatible with specified
Fluidmesh devices.
Table 7. Device plug-in compatibility (FM 1000 to FM 1300 OTTO)
Plugin FM 1000
Gateway
FM 10000
Gateway
FM PONTE
50
FM 1200
VOLO
FM 1300
OTTO
Bandwidth Available Not available Available Available
Bandwidth
upgrade
Available Not available Available Available
Fluidity-
Bandwidth
(Mobile)
Not available Not available Not
available
Not available
Fluidity-
Bandwidth
(Trackside)
Not available Not available Not
available
Not available
Fluidity Firmware
embedded
Not available Available Not available
4.9 GHz band Not available Not available Available Not available
Licensed
frequencies
Not available Not available Available Not available
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 153 of 180