Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
Plug-in Is the plug-
in package
removable
and re-
installable?
Function Part number
Fluidity-
Bandwidth
(Mobile)
Yes Enables Fluidity capability for
mobile Fluidmesh devices.
Allows traffic forwarding up to
and including the amount of
bandwidth specified in the
part number.
FM[model
number]-MOB-
MOB-[bandwidth
limit] (FMx200
models)
FM[model
number]-FLU-
MOB-[bandwidth
limit] (FMx500
models)
Fluidity-
Bandwidth
(Trackside)
Yes Enables Fluidity capability for
static-mount Fluidmesh
devices.
Allows traffic forwarding up to
and including the amount of
bandwidth specified in the
part number.
FM[model
number]-MOB-
TRK-[bandwidth
limit] (FMx200
models)
FM[model
number]-FLU-
TRK-[bandwidth
limit] (FMx500
models)
4.9 GHz band Yes Enables operation in the 4.9
GHz emergency band.
Note that the 4.9 GHz band is
not available in Brazil and
Canada.
FM-49
Licensed
Frequencies
Yes Enables the use of any
operating frequency,
regardless of country
selection.
FM-LF
World
Frequencies
No Unlocks the country drop-
down selector on units sold in
territories where the selector
is locked.
FM-WORLD
AES Yes Enables data exchange
according to the regular
Advanced Encryption
Standard.
FM-AES
Fluidmesh
Access Points
Yes Enables WiFi access-point
capability.
FM-AP
VLAN Yes Enables virtual LAN
capability.
FM-VLAN
Virtual Gigabit Yes Enables Fluidmesh Virtual
Gigabit capability.
FM-VGBE
L2TP Yes Enables layer 2 transfer
protocol capability.
FM-L2TP
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 152 of 180