Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
7. SOFTWARE PLUG-INS
7.1. Available plug-ins
Like other Fluidmesh radio transceivers, the Fluidmesh 4200 FIBER is
able to take advantage of plug-in software upgrades that add features and
enhance the performance of the unit.
The following table lists all available software plug-ins for all Fluidmesh
hardware devices, their specific functions, and their plug-in part numbers.
The tables that follow this table describe which plug-ins are compatible
with specified Fluidmesh devices.
Table 6. Available Fluidmesh software plug-ins
Plug-in Is the plug-
in package
removable
and re-
installable?
Function Part number
Bandwidth Yes A range of plug-ins are
available to enable increased
traffic forwarding bandwidth,
up to and including the
amount of bandwidth
specified in the part number
(including unlimited
bandwidth).
FM[model
number]-
[bandwidth limit]
Bandwidth
upgrade
Yes If an existing bandwidth plug-
in is installed, this plug-in
allows bandwidth to be
upgraded to a higher,
specified value.
Note that if a bandwidth
upgrade plug-in is removed,
the unit's bandwidth
capability is not restored to
the level of the previous
upgrade (if any). Rather, the
bandwidth capability is
restored to the factory default
level.
FM[model
number]-UPG-
[existing
bandwidth
limit/new
bandwidth limit]
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 151 of 180