Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
IMPORTANT
To minimize impact on overall system performance, wireless
AP bandwidth is limited to 5 Mb/s. This is sufficient for
maintenance purposes, but is not sufficient to support normal
wireless carrier operations.
To enable the wireless AP feature on the Fluidmesh 4200 FIBER, do the
following steps:
1. Make sure that the FM-AP software plug-in is installed on the
radio unit. For instructions on how to install the FM-AP plug-in,
refer to “Plug-in management procedures” (page 155).
IMPORTANT
If the FM-AP plug-in is not installed on the radio unit,
the –Fluidmesh WiFi link will not appear in the left-
hand settings menu.
2. Open the FLUIDMESH 802.11 INTERFACE dialog (below) by
clicking the –Fluidmesh WiFi link under ADVANCED SETTINGS
in the left-hand settings menu.
To configure the radio unit as a bridged or routed wireless access point
(AP), do the following steps:
1. Configure the radio unit as a wireless access point by clicking the
WLAN MODE drop-down menu and selecting the AP option.
• The FLUIDMESH 802.11 INTERFACE dialog will show
additional options (below):
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 115 of 180