Installation Instructions
Table Of Contents
- Fluidmesh 4200 FIBER
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Hardware installation
- 4.1. Fluidmesh Hardware Installation
- 4.2. Connecting the Fluidmesh Fluidmesh 4200 FIBER to a network and antennas
- 5. Using the Fluidmesh Partner Portal
- 6. Device configuration using the configurator interface
- 6.1. Software and hardware prerequisites
- 6.2. Accessing the Fluidmesh 4200 FIBER for device configuration
- 6.3. Switching between offline and online modes
- 6.4. General settings
- 6.5. Network control
- 6.6. Advanced settings
- 6.6.1. Advanced radio settings
- 6.6.2. SFP settings
- 6.6.3. Static routes
- 6.6.4. Whitelists and Blacklists
- 6.6.5. Multicast
- 6.6.6. SNMP configuration
- 6.6.7. Wireless access point configuration
- 6.6.8. RADIUS configuration
- 6.6.9. NTP Configuration
- 6.6.10. L2TP configuration
- 6.6.11. VLAN settings
- 6.6.12. Fluidity settings
- 6.6.13. Miscellaneous settings
- 6.7. Management settings
- 6.7.1. View Mode settings
- 6.7.2. Changing the Administrator username and password
- 6.7.3. Overwriting and upgrading the unit firmware
- 6.7.4. Plug-In management
- 6.7.5. The device status view
- 6.7.6. Saving and restoring the unit settings
- 6.7.7. Resetting the unit to factory defaults
- 6.7.8. Logging out
- 6.7.9. Viewing the end-user license agreement
- 7. Software Plug-Ins
- 8. Troubleshooting
- 9. Electrical power requirements
- 10. Heat radiation data
- 11. Federal Communications Commission (FCC) radio interference statement
- 12. Notices and copyright
- 13. Fluidmesh end-user license agreement
- 13.1. Preamble
- 13.2. Notice
- 13.3. Definitions
- 13.4. License grant
- 13.5. Uses and restrictions on use
- 13.6. Open-source software
- 13.7. Termination
- 13.8. Feedback
- 13.9. Consent to use of data
- 13.10. Warranty disclaimer
- 13.11. Limitation of liability
- 13.12. Exclusion of liability for emergency services
- 13.13. Export control
- 13.14. General
- 14. Contact us
To let the system choose the optimal Maximum link length setting and
MAC layer timeouts automatically, check the Automatic check-box.
6.6.2. SFP settings
IMPORTANT
The Fluidmesh 4200 FIBER is shipped from the factory with no
fiber-optic transceiver installed.
For the unit to have fiber-optic capability, the SFP port must be
equipped with a separately-available XCO-type fiber-optic
transceiver.
XCO-standard transceiver modules and XCO-type duplex
fiber-optic connectors can easily be sourced as off-the-shelf
parts. If you experience difficulty in sourcing or ordering fiber-
optic parts or accessories, please contact your local Fluidmesh
Networks representative for assistance.
The SFP/ETHERNET SETTINGS window contains controls to change the
data exchange speeds of the unit's duplex fibre-optic link and RJ45
Ethernet port.
To change the data exchange speed of the fibre-optic link and/or Ethernet
link, do the following steps:
1. Click the -ethernet settings link under ADVANCED SETTINGS
in the left-hand settings menu.
• The SFP/ETHERNET SETTINGS dialog will be shown
(Figure 48 (page 102)).
Figure 48. Configurator GUI (SFP/ETHERNET
SETTINGS dialog)
2. Choose the correct fiber-optic data exchange speed by clicking
the SFP speed drop-down and clicking the correct option.
3. Choose the correct Ethernet data exchange speed by clicking the
Ethernet speed drop-down and clicking the correct option.
Fluidmesh 4200 FIBER
© Fluidmesh Networks LLC Page 102 of 180