Installation Instructions
Table Of Contents
- Cisco Ultra-Reliable Wireless Backhaul FM3200 Endo
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.2. Connecting the Cisco FM3200 Endo to networking and communications hardware
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Cisco FM3200 Endo for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.5.1. Ping softdog
- 7.5.2. FM-QUADRO
- FM-QUADRO for mesh network-capable devices
- Plotting and interpreting the wireless links
- Viewing live data for a radio or wireless link
- Viewing live RSSI data for a wireless link
- Manipulating the FM-QUADRO view
- Changing the relative position of device icons
- Showing KPI values for wireless links
- Adding an aerial map to the FM-QUADRO view
- Adjusting the transparency of the aerial map view
- Exporting a network representation file
- 7.5.3. Advanced tools
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Ethernet settings
- 7.6.4. Static routes
- 7.6.5. Pass lists and Block lists
- 7.6.6. Multicast
- 7.6.7. SNMP configuration
- 7.6.8. Wireless access point configuration
- 7.6.9. RADIUS configuration
- 7.6.10. NTP Configuration
- 7.6.11. L2TP configuration
- 7.6.12. VLAN settings
- 7.6.13. Fluidity settings
- 7.6.14. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the FM Racer interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in FM Racer
- 9.6. I cannot connect my Fluidmesh device to the FM Racer interface
- 9.7. I applied configuration settings to the device using FM Racer, but I have lost connection to the device in FM Racer.
- 9.8. How do I connect an existing pre-FM Racer device to FM Racer?
- 10. Electrical power requirements
- 11. Heat radiation data
- 12. Federal Communications Commission (FCC) radio interference statement
- 13. Notices and copyright
- 14. Fluidmesh end-user license agreement
- 14.1. Preamble
- 14.2. Notice
- 14.3. Definitions
- 14.4. License grant
- 14.5. Uses and restrictions on use
- 14.6. Open-source software
- 14.7. Termination
- 14.8. Feedback
- 14.9. Consent to use of data
- 14.10. Warranty disclaimer
- 14.11. Limitation of liability
- 14.12. Exclusion of liability for emergency services
- 14.13. Export control
- 14.14. General
- 15. Contact us
Figure 21. Configurator window heading block
If the unit has been set to Bridge Mode, you must set the Bridge ID of the
remote unit to which the local unit must be linked. Set the Bridge ID by
doing the following steps:
1. Click the Remote [Unit model] Bridge ID: drop-down (Figure 22
(page 58)).
Figure 22. General Mode window (Remote Bridge Unit
section)
2. Click one of the following options:
• AUTO: The local unit will automatically establish a wireless
bridge connection with the closest available Fluidmesh unit
that is set to Bridge Mode.
• Alternatively, choose the correct unit from the list of
available units.
3. Save the operational mode settings by clicking the Save button.
Alternatively, clear the settings by clicking the Reset button.
Changing the Prodigy version
IMPORTANT
Prodigy version selection is only available if the Cisco FM3200
Endo is set to Mesh Point mode or Mesh End mode. If the
unit is set to Bridge mode, the Prodigy Version selector will not
be available.
The Prodigy Version box (below) contains the Prodigy version selector.
Cisco Ultra-Reliable Wireless
Backhaul FM3200 Endo
© 2020 Cisco and/or its affiliates. All rights reserved. Page 58 of 177