Installation Instructions
Table Of Contents
- Cisco Ultra-Reliable Wireless Backhaul FM3200 Endo
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.2. Connecting the Cisco FM3200 Endo to networking and communications hardware
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Cisco FM3200 Endo for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.5.1. Ping softdog
- 7.5.2. FM-QUADRO
- FM-QUADRO for mesh network-capable devices
- Plotting and interpreting the wireless links
- Viewing live data for a radio or wireless link
- Viewing live RSSI data for a wireless link
- Manipulating the FM-QUADRO view
- Changing the relative position of device icons
- Showing KPI values for wireless links
- Adding an aerial map to the FM-QUADRO view
- Adjusting the transparency of the aerial map view
- Exporting a network representation file
- 7.5.3. Advanced tools
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Ethernet settings
- 7.6.4. Static routes
- 7.6.5. Pass lists and Block lists
- 7.6.6. Multicast
- 7.6.7. SNMP configuration
- 7.6.8. Wireless access point configuration
- 7.6.9. RADIUS configuration
- 7.6.10. NTP Configuration
- 7.6.11. L2TP configuration
- 7.6.12. VLAN settings
- 7.6.13. Fluidity settings
- 7.6.14. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the FM Racer interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in FM Racer
- 9.6. I cannot connect my Fluidmesh device to the FM Racer interface
- 9.7. I applied configuration settings to the device using FM Racer, but I have lost connection to the device in FM Racer.
- 9.8. How do I connect an existing pre-FM Racer device to FM Racer?
- 10. Electrical power requirements
- 11. Heat radiation data
- 12. Federal Communications Commission (FCC) radio interference statement
- 13. Notices and copyright
- 14. Fluidmesh end-user license agreement
- 14.1. Preamble
- 14.2. Notice
- 14.3. Definitions
- 14.4. License grant
- 14.5. Uses and restrictions on use
- 14.6. Open-source software
- 14.7. Termination
- 14.8. Feedback
- 14.9. Consent to use of data
- 14.10. Warranty disclaimer
- 14.11. Limitation of liability
- 14.12. Exclusion of liability for emergency services
- 14.13. Export control
- 14.14. General
- 15. Contact us
• FLUIDITY FREQUENCY SCAN tab (Used where
mobile Fluidity units are configured with different
frequencies.)
• SPANNING TREE tab (Allows you to build a logical
topology for Ethernet networks, including backup links
to provide fault tolerance if an active link fails.)
• QOS tab (Contains controls for Quality of Service and
Class of Service settings.)
• MPLS tab (Contains controls for adjustment of the unit's
multiprotocol label switching settings.)
• FAST FAILOVER (TITAN) tab (Contains controls to
enable fast fail-over capability on networks where
backup units are installed.)
• ARP tab (Contains controls for Address Resolution
Protocol settings used for discovering MAC addresses
that are associated with IP addresses.)
• INTRA-CAR tab (Contains controls to create and
maintain a wireless backbone network throughout
physically large, compartmentalized vehicles.)
For a detailed description of the configuration options featured
in the FM Racer interface, refer to the Available configuration
parameters section of the Fluidmesh Networks FM Racer User
Manual.
7.1. Software and hardware prerequisites
To access the Configurator graphical user interface (GUI) and use the
Configurator to program the Cisco FM3200 Endo, you need the following:
• A desktop, laptop or tablet computer equipped with:
• Any current web browser. For a list of compatible web
browsers, refer to the Supported web browsers table in
“Using the Fluidmesh Partner Portal” (page 40).
• Any Microsoft Windows, Mac OS or Linux operating system.
• An integrated Ethernet port.
• A CAT5/6 Ethernet cable with an RJ45 connector at each end.
7.2. Accessing the Cisco FM3200 Endo for device
configuration
Before the unit can be made part of a wireless network, it must be
configured.
The on-board Configurator can be used to configure a Fluidmesh device
in either of two ways:
• By connecting a control device directly to the Fluidmesh device
using an Ethernet cable (Local access)
Cisco Ultra-Reliable Wireless
Backhaul FM3200 Endo
© 2020 Cisco and/or its affiliates. All rights reserved. Page 47 of 177