Installation Instructions
Table Of Contents
- Cisco Ultra-Reliable Wireless Backhaul FM3200 Endo
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.2. Connecting the Cisco FM3200 Endo to networking and communications hardware
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Cisco FM3200 Endo for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.5.1. Ping softdog
- 7.5.2. FM-QUADRO
- FM-QUADRO for mesh network-capable devices
- Plotting and interpreting the wireless links
- Viewing live data for a radio or wireless link
- Viewing live RSSI data for a wireless link
- Manipulating the FM-QUADRO view
- Changing the relative position of device icons
- Showing KPI values for wireless links
- Adding an aerial map to the FM-QUADRO view
- Adjusting the transparency of the aerial map view
- Exporting a network representation file
- 7.5.3. Advanced tools
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Ethernet settings
- 7.6.4. Static routes
- 7.6.5. Pass lists and Block lists
- 7.6.6. Multicast
- 7.6.7. SNMP configuration
- 7.6.8. Wireless access point configuration
- 7.6.9. RADIUS configuration
- 7.6.10. NTP Configuration
- 7.6.11. L2TP configuration
- 7.6.12. VLAN settings
- 7.6.13. Fluidity settings
- 7.6.14. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the FM Racer interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in FM Racer
- 9.6. I cannot connect my Fluidmesh device to the FM Racer interface
- 9.7. I applied configuration settings to the device using FM Racer, but I have lost connection to the device in FM Racer.
- 9.8. How do I connect an existing pre-FM Racer device to FM Racer?
- 10. Electrical power requirements
- 11. Heat radiation data
- 12. Federal Communications Commission (FCC) radio interference statement
- 13. Notices and copyright
- 14. Fluidmesh end-user license agreement
- 14.1. Preamble
- 14.2. Notice
- 14.3. Definitions
- 14.4. License grant
- 14.5. Uses and restrictions on use
- 14.6. Open-source software
- 14.7. Termination
- 14.8. Feedback
- 14.9. Consent to use of data
- 14.10. Warranty disclaimer
- 14.11. Limitation of liability
- 14.12. Exclusion of liability for emergency services
- 14.13. Export control
- 14.14. General
- 15. Contact us
5.2.2. Connecting LAN cables to the unit
Bottom housing and RJ45 LAN cables
IMPORTANT
The FM3200 Endo is ingress-protection rated to standards
specified by EN 50155 and EN 45545.
To ensure the FM3200 Endo remains waterproof and
dustproof, follow all instructions in this section. Following the
instructions in this section will also ensure that the is well
prepared for any ingress-protection testing.
When the Cisco FM3200 Endo is mounted in its final location, connect the
unit to LAN connection(s) and a PoE power supply by doing the following
steps:
1. Only use shielded CAT5/6 cables that terminate in RJ45 Ethernet
connectors at both ends.
2. Make sure that the terminal pin assignments for the RJ45 plugs
comply with the accepted standard for RJ45 LAN/PoE
connectors.
Next, proceed to the steps in the following table:
3. Remove the two screws from the
bottom housing.
4. Separate the bottom housing from the
main body of the unit.
5. Route the LAN cables through the hexagon
nut, then through the rubber seal, then through
the cable gland nut.
Cisco Ultra-Reliable Wireless
Backhaul FM3200 Endo
© 2020 Cisco and/or its affiliates. All rights reserved. Page 35 of 177