Installation Instructions
Table Of Contents
- Cisco Ultra-Reliable Wireless Backhaul FM3200 Endo
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.2. Connecting the Cisco FM3200 Endo to networking and communications hardware
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Cisco FM3200 Endo for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.5.1. Ping softdog
- 7.5.2. FM-QUADRO
- FM-QUADRO for mesh network-capable devices
- Plotting and interpreting the wireless links
- Viewing live data for a radio or wireless link
- Viewing live RSSI data for a wireless link
- Manipulating the FM-QUADRO view
- Changing the relative position of device icons
- Showing KPI values for wireless links
- Adding an aerial map to the FM-QUADRO view
- Adjusting the transparency of the aerial map view
- Exporting a network representation file
- 7.5.3. Advanced tools
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Ethernet settings
- 7.6.4. Static routes
- 7.6.5. Pass lists and Block lists
- 7.6.6. Multicast
- 7.6.7. SNMP configuration
- 7.6.8. Wireless access point configuration
- 7.6.9. RADIUS configuration
- 7.6.10. NTP Configuration
- 7.6.11. L2TP configuration
- 7.6.12. VLAN settings
- 7.6.13. Fluidity settings
- 7.6.14. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the FM Racer interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in FM Racer
- 9.6. I cannot connect my Fluidmesh device to the FM Racer interface
- 9.7. I applied configuration settings to the device using FM Racer, but I have lost connection to the device in FM Racer.
- 9.8. How do I connect an existing pre-FM Racer device to FM Racer?
- 10. Electrical power requirements
- 11. Heat radiation data
- 12. Federal Communications Commission (FCC) radio interference statement
- 13. Notices and copyright
- 14. Fluidmesh end-user license agreement
- 14.1. Preamble
- 14.2. Notice
- 14.3. Definitions
- 14.4. License grant
- 14.5. Uses and restrictions on use
- 14.6. Open-source software
- 14.7. Termination
- 14.8. Feedback
- 14.9. Consent to use of data
- 14.10. Warranty disclaimer
- 14.11. Limitation of liability
- 14.12. Exclusion of liability for emergency services
- 14.13. Export control
- 14.14. General
- 15. Contact us
To convert a License code into an Activation code for a Fluidmesh device,
do the following steps:
1. Log on to the Fluidmesh Partner Portal.
2. Click the Plug-ins link.
• When you purchase a generic 16-digit License code, the
License code and corresponding plug-in will be listed on
the Plug-ins page (Figure 65 (page 148)).
Figure 65. Partner Portal Plug-ins page (License code
plug-in)
• When the generic License code was purchased, you will
have received an E-mail from plugins@fluidmesh.com
containing the License code. If the License code and
corresponding plug-in are not listed on the Plug-ins page,
click the Add button in the upper left-hand corner of the
Plug-ins web page, and enter the License code using the
dialog.
3. Enter the unit identification number (5.a.b.c) or the unit serial
number of the Fluidmesh unit in the Mesh ID - Serial Number
field.
4. If needed, enter the name of the relevant technical project in the
Project Name field.
Cisco Ultra-Reliable Wireless
Backhaul FM3200 Endo
© 2020 Cisco and/or its affiliates. All rights reserved. Page 148 of 177