Installation Instructions
Table Of Contents
- Cisco Ultra-Reliable Wireless Backhaul FM3200 Endo
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.2. Connecting the Cisco FM3200 Endo to networking and communications hardware
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Cisco FM3200 Endo for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.5.1. Ping softdog
- 7.5.2. FM-QUADRO
- FM-QUADRO for mesh network-capable devices
- Plotting and interpreting the wireless links
- Viewing live data for a radio or wireless link
- Viewing live RSSI data for a wireless link
- Manipulating the FM-QUADRO view
- Changing the relative position of device icons
- Showing KPI values for wireless links
- Adding an aerial map to the FM-QUADRO view
- Adjusting the transparency of the aerial map view
- Exporting a network representation file
- 7.5.3. Advanced tools
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Ethernet settings
- 7.6.4. Static routes
- 7.6.5. Pass lists and Block lists
- 7.6.6. Multicast
- 7.6.7. SNMP configuration
- 7.6.8. Wireless access point configuration
- 7.6.9. RADIUS configuration
- 7.6.10. NTP Configuration
- 7.6.11. L2TP configuration
- 7.6.12. VLAN settings
- 7.6.13. Fluidity settings
- 7.6.14. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the FM Racer interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in FM Racer
- 9.6. I cannot connect my Fluidmesh device to the FM Racer interface
- 9.7. I applied configuration settings to the device using FM Racer, but I have lost connection to the device in FM Racer.
- 9.8. How do I connect an existing pre-FM Racer device to FM Racer?
- 10. Electrical power requirements
- 11. Heat radiation data
- 12. Federal Communications Commission (FCC) radio interference statement
- 13. Notices and copyright
- 14. Fluidmesh end-user license agreement
- 14.1. Preamble
- 14.2. Notice
- 14.3. Definitions
- 14.4. License grant
- 14.5. Uses and restrictions on use
- 14.6. Open-source software
- 14.7. Termination
- 14.8. Feedback
- 14.9. Consent to use of data
- 14.10. Warranty disclaimer
- 14.11. Limitation of liability
- 14.12. Exclusion of liability for emergency services
- 14.13. Export control
- 14.14. General
- 15. Contact us
IMPORTANT
A different DHCP IP address class must be
assigned to every FM1200 Volo, Cisco 3200-
series and Cisco 4200-series radio in the
network. This will help avoid IP conflicts
between different access points.
To configure the radio unit as a DHCP or static-protocol wireless station
(STA), do the following steps:
1. Configure the radio unit as a wireless station by clicking the
WLAN MODE drop-down menu and selecting the STA option.
• The FLUIDMESH 802.11 INTERFACE dialog will show
additional options (below):
2.
To enable network address translation, check the Network
Address Translation check-box.
3. Choose the encryption protocol that will be used to encrypt
communication to and from connected clients by clicking the
WLAN Security drop-down, and choosing a suitable security
option.
4. The radio unit will broadcast the SSID shown in the WLAN SSID
field. If needed, change the SSID manually.
5. When maintenance personnel connect to the unit using the AP,
they will be prompted to enter a secret passphrase. Type a
chosen passphrase in the WLAN Passphrase entry field.
6. To show the WLAN passphrase in plain text as it is being entered,
check the Show Passphrase check-box.
Cisco Ultra-Reliable Wireless
Backhaul FM3200 Endo
© 2020 Cisco and/or its affiliates. All rights reserved. Page 108 of 177