Installation Instructions
Table Of Contents
- Cisco Ultra-Reliable Wireless Backhaul FM4200 Mobi
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh Hardware Installation
- 5.2. Connecting the Fluidmesh Cisco FM4200 Mobi to a network and antennas
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Cisco FM4200 Mobi for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.5.1. Ping softdog
- 7.5.2. FM-QUADRO
- FM-QUADRO for mesh network-capable devices
- Plotting and interpreting the wireless links
- Viewing live data for a radio or wireless link
- Viewing live RSSI data for a wireless link
- Manipulating the FM-QUADRO view
- Changing the relative position of device icons
- Showing KPI values for wireless links
- Adding an aerial map to the FM-QUADRO view
- Adjusting the transparency of the aerial map view
- Exporting a network representation file
- 7.5.3. Advanced tools
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Static routes
- 7.6.4. Pass lists and Block lists
- 7.6.5. Multicast
- 7.6.6. SNMP configuration
- 7.6.7. Wireless access point configuration
- 7.6.8. RADIUS configuration
- 7.6.9. NTP Configuration
- 7.6.10. L2TP configuration
- 7.6.11. VLAN settings
- 7.6.12. Fluidity settings
- 7.6.13. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 10. Electrical power requirements
- 11. Heat radiation data
- 12. Federal Communications Commission (FCC) radio interference statement
- 13. Notices and copyright
- 14. Fluidmesh end-user license agreement
- 14.1. Preamble
- 14.2. Notice
- 14.3. Definitions
- 14.4. License grant
- 14.5. Uses and restrictions on use
- 14.6. Open-source software
- 14.7. Termination
- 14.8. Feedback
- 14.9. Consent to use of data
- 14.10. Warranty disclaimer
- 14.11. Limitation of liability
- 14.12. Exclusion of liability for emergency services
- 14.13. Export control
- 14.14. General
- 15. Contact us
• Mesh Point Mode: This is the default operating mode. Each radio
transceiver unit that is part of the network, but is not connected to
the wired LAN backbone, must be set in Mesh Point mode.
• Mesh End Mode: Each radio transceiver unit that is part of the
network and is connected to the wired LAN backbone must be set
in Mesh End Mode. A Mesh End transceiver unit is always the
junction point between the wireless network and any IP-based wired
network.
Network addressing
Fluidmesh radio transceivers
Fluidmesh data link layer (layer 2) addressing allows you to configure
each Cisco FM4200 Mobi transceiver unit, and each IP device connected
to the unit, according to the IP address class used in the private LAN to
which the Mesh End unit is connected.
Each Fluidmesh radio transceiver unit has a factory-set IP address of
192.168.0.10, and a Netmask of 255.255.255.0.
NOTE
Each individual Fluidmesh radio transceiver unit has a factory-
set 5.a.b.c Mesh identification number. Each unit is shipped
from the factory with the same IP address, but with a unique
Mesh identification number.
When a Fluidmesh wireless network is connected to a wired LAN, the
LAN is usually the private control room LAN. Therefore, Fluidmesh radio
transceivers, and all other edge devices that connect the wireless network
to the wired LAN, must be assigned individual LAN IP addresses that are
part of the same subnet. The edge devices will be accessed using those
IP addresses.
A typical network configuration (Fluidmesh Network Addressing) is shown
in “Operating the unit in Mesh Point mode or Mesh End mode” (page 22).
In this configuration, the private LAN IP address class is 192.168.150.0,
with netmask 255.255.255.0. Note that each device has an IP address
belonging to this subnet.
IMPORTANT
IP addresses must not be duplicated within a network. If
addresses are duplicated, IP address conflicts will occur.
Multiple Fluidmesh radio transceiver units can be connected through a
network switch, forming radio clusters. The proprietary routing protocol will
run automatically on the wired part of the network. To activate the cluster
feature, transceiver units that are capable of being set in Mesh Point
mode must be set in that mode.
Cisco Ultra-Reliable Wireless
Backhaul FM4200 Mobi
© 2020 Cisco and/or its affiliates. All rights reserved. Page 23 of 177