Installation Instructions
Table Of Contents
- Cisco Ultra-Reliable Wireless Backhaul FM4200 Mobi
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh Hardware Installation
- 5.2. Connecting the Fluidmesh Cisco FM4200 Mobi to a network and antennas
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Cisco FM4200 Mobi for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.5.1. Ping softdog
- 7.5.2. FM-QUADRO
- FM-QUADRO for mesh network-capable devices
- Plotting and interpreting the wireless links
- Viewing live data for a radio or wireless link
- Viewing live RSSI data for a wireless link
- Manipulating the FM-QUADRO view
- Changing the relative position of device icons
- Showing KPI values for wireless links
- Adding an aerial map to the FM-QUADRO view
- Adjusting the transparency of the aerial map view
- Exporting a network representation file
- 7.5.3. Advanced tools
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Static routes
- 7.6.4. Pass lists and Block lists
- 7.6.5. Multicast
- 7.6.6. SNMP configuration
- 7.6.7. Wireless access point configuration
- 7.6.8. RADIUS configuration
- 7.6.9. NTP Configuration
- 7.6.10. L2TP configuration
- 7.6.11. VLAN settings
- 7.6.12. Fluidity settings
- 7.6.13. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 10. Electrical power requirements
- 11. Heat radiation data
- 12. Federal Communications Commission (FCC) radio interference statement
- 13. Notices and copyright
- 14. Fluidmesh end-user license agreement
- 14.1. Preamble
- 14.2. Notice
- 14.3. Definitions
- 14.4. License grant
- 14.5. Uses and restrictions on use
- 14.6. Open-source software
- 14.7. Termination
- 14.8. Feedback
- 14.9. Consent to use of data
- 14.10. Warranty disclaimer
- 14.11. Limitation of liability
- 14.12. Exclusion of liability for emergency services
- 14.13. Export control
- 14.14. General
- 15. Contact us
14.7. Termination
This license will continue until terminated. Unauthorized copying of the
Fluidmesh Firmware or failure to comply with the above restrictions will
result in automatic termination of this Agreement and will make other legal
remedies available to Fluidmesh. This license will also automatically
terminate if you go into liquidation, suffer or make any winding-up petition,
make an arrangement with your creditors, or suffer or file any similar
action in any jurisdiction in consequence of debt.
Furthermore, Fluidmesh may immediately terminate this Agreement if (i)
you fail to cure a breach of this Agreement (other than a breach pursuant
to Fluidmesh intellectual property rights) within thirty (30) calendar days
after its receipt of written notice regarding such breach, or (ii) you breach
any Fluidmesh intellectual property right. Upon termination of this license
for any reason, you agree to destroy all copies of the Fluidmesh
Firmware. Any use of the Fluidmesh Firmware after termination is
unlawful.
14.8. Feedback
You may provide suggestions, comments or other feedback ('Feedback')
with respect to Fluidmesh Firmware, and Fluidmesh Devices. Feedback,
even if designated as confidential by you, shall not impose any
confidentiality obligations on Fluidmesh. You agree that Fluidmesh is free
to use, disclose, reproduce, license or otherwise distribute and exploit any
Feedback provided by you as Fluidmesh sees fit, entirely without
obligation or restriction of any kind on account of intellectual property
rights, or otherwise.
14.9. Consent to use of data
You acknowledge and agree that Fluidmesh may, directly or indirectly
through the services of third parties, collect and store information
regarding the use and performance of the Fluidmesh Firmware and
Fluidmesh Devices, and about equipment through which it otherwise is
accessed and used.
You further agree that Fluidmesh may use such information for any
purpose related to any use of the Fluidmesh Firmware and Fluidmesh
Devices by you, including, without limitation, improving the performance of
the Fluidmesh Firmware or developing updates and verifying your
compliance with the terms of this Agreement and enforcing Fluidmesh’s
rights, including all intellectual property rights in and to the Fluidmesh
Firmware.
Fluidmesh shall have the right to collect and analyze data and other
information relating to the provision, use and performance of various
aspects of the Fluidmesh Firmware and Fluidmesh Devices and related
systems and technologies ('Data'), and you give Fluidmesh the right to
use and disclose such Data (during and after the term of this Agreement)
Cisco Ultra-Reliable Wireless
Backhaul FM4200 Mobi
© 2020 Cisco and/or its affiliates. All rights reserved. Page 173 of 177