Installation Instructions
Table Of Contents
- Cisco Ultra-Reliable Wireless Backhaul FM4200 Mobi
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh Hardware Installation
- 5.2. Connecting the Fluidmesh Cisco FM4200 Mobi to a network and antennas
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Cisco FM4200 Mobi for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.5.1. Ping softdog
- 7.5.2. FM-QUADRO
- FM-QUADRO for mesh network-capable devices
- Plotting and interpreting the wireless links
- Viewing live data for a radio or wireless link
- Viewing live RSSI data for a wireless link
- Manipulating the FM-QUADRO view
- Changing the relative position of device icons
- Showing KPI values for wireless links
- Adding an aerial map to the FM-QUADRO view
- Adjusting the transparency of the aerial map view
- Exporting a network representation file
- 7.5.3. Advanced tools
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Static routes
- 7.6.4. Pass lists and Block lists
- 7.6.5. Multicast
- 7.6.6. SNMP configuration
- 7.6.7. Wireless access point configuration
- 7.6.8. RADIUS configuration
- 7.6.9. NTP Configuration
- 7.6.10. L2TP configuration
- 7.6.11. VLAN settings
- 7.6.12. Fluidity settings
- 7.6.13. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 10. Electrical power requirements
- 11. Heat radiation data
- 12. Federal Communications Commission (FCC) radio interference statement
- 13. Notices and copyright
- 14. Fluidmesh end-user license agreement
- 14.1. Preamble
- 14.2. Notice
- 14.3. Definitions
- 14.4. License grant
- 14.5. Uses and restrictions on use
- 14.6. Open-source software
- 14.7. Termination
- 14.8. Feedback
- 14.9. Consent to use of data
- 14.10. Warranty disclaimer
- 14.11. Limitation of liability
- 14.12. Exclusion of liability for emergency services
- 14.13. Export control
- 14.14. General
- 15. Contact us
13. NOTICES AND COPYRIGHT
WARNING
Installation of Fluidmesh hardware devices and their
supporting infrastructure must be done by suitably qualified
personnel only. In some countries, installation by a certified
electrician may be required.
Fluidmesh hardware installations must comply with all
applicable local legislation.
WARNING
Never disassemble a Fluidmesh hardware device to any extent
that is not described in the relevant device user's manual.
Fluidmesh devices contain no user-serviceable parts.
Disassembling a Fluidmesh hardware device will invalidate the
device warranty, and may compromise the operational integrity
of the device.
On some Fluidmesh radio transceiver devices, the lower
access cover must be removed to gain access to the hardware
Reset button. Do not operate a radio transceiver device for
extended periods if its lower access cover has been removed.
WARNING
To avoid danger from non-ionizing radiation and/or electric
shock and/or high-intensity laser or LED light sources, be sure
to install the unit only in a location with restricted access.
WARNING
To avoid danger from electric shock, do not expose the unit to
water or high humidity if the unit is powered ON, or if any
access covers have been removed from the unit enclosure.
Do not place liquid-filled objects on or above the unit.
NOTICE TO THE USER
Copyright © 2020 Cisco and/or its affiliates. All rights reserved. This
manual and the software described herein shall not, in whole or in part, be
reproduced, translated or reduced to any machine-readable form without
the prior written consent of Cisco Systems.
Cisco and/or its affiliates provides no warranty with regard to this manual,
software or other information contained herein, and hereby expressly
disclaims any implied warranties of merchantability or fitness for any
particular purpose with regard to this manual, the software or such other
Cisco Ultra-Reliable Wireless
Backhaul FM4200 Mobi
© 2020 Cisco and/or its affiliates. All rights reserved. Page 168 of 177