Installation Instructions
Table Of Contents
- Cisco Ultra-Reliable Wireless Backhaul FM4200 Mobi
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh Hardware Installation
- 5.2. Connecting the Fluidmesh Cisco FM4200 Mobi to a network and antennas
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Cisco FM4200 Mobi for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.5.1. Ping softdog
- 7.5.2. FM-QUADRO
- FM-QUADRO for mesh network-capable devices
- Plotting and interpreting the wireless links
- Viewing live data for a radio or wireless link
- Viewing live RSSI data for a wireless link
- Manipulating the FM-QUADRO view
- Changing the relative position of device icons
- Showing KPI values for wireless links
- Adding an aerial map to the FM-QUADRO view
- Adjusting the transparency of the aerial map view
- Exporting a network representation file
- 7.5.3. Advanced tools
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Static routes
- 7.6.4. Pass lists and Block lists
- 7.6.5. Multicast
- 7.6.6. SNMP configuration
- 7.6.7. Wireless access point configuration
- 7.6.8. RADIUS configuration
- 7.6.9. NTP Configuration
- 7.6.10. L2TP configuration
- 7.6.11. VLAN settings
- 7.6.12. Fluidity settings
- 7.6.13. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 10. Electrical power requirements
- 11. Heat radiation data
- 12. Federal Communications Commission (FCC) radio interference statement
- 13. Notices and copyright
- 14. Fluidmesh end-user license agreement
- 14.1. Preamble
- 14.2. Notice
- 14.3. Definitions
- 14.4. License grant
- 14.5. Uses and restrictions on use
- 14.6. Open-source software
- 14.7. Termination
- 14.8. Feedback
- 14.9. Consent to use of data
- 14.10. Warranty disclaimer
- 14.11. Limitation of liability
- 14.12. Exclusion of liability for emergency services
- 14.13. Export control
- 14.14. General
- 15. Contact us
Parameter Default value
User All other traffic
Packet tagged with MVID Packet passed
Access port rules for incoming packets (Case and Action)
Untagged packet from Fluidmesh device Packet passed
Untagged packet, VID not configured Packet passed
Untagged packet, VID configured Packet tagged with specified VID
Tagged packet with valid VID Packet dropped
Tagged packet with null (0) VID Packet dropped
Access port rules for outgoing packets (Case and Action)
Tagged packet with configured and
allowed VID
Packet passed
Packet from Fluidmesh device Packet passed
Tagged packet, port VID not configured Packet passed
Tagged packet with valid but disallowed
VID
Packet dropped
Tagged packet with null (0) VID Packet dropped
Access port rules for incoming packets with unit in Smart Mode (Case and
Action)
Untagged packet If native VLAN = ON: Packet passed
(tagged with NVID)
If native VLAN = OFF: Packet dropped
Tagged packet (any VID, no checks) Packet passed with original tag
Access port rules for outgoing packets with unit in Smart Mode (Case and
Action)
Packets originating from Fluidmesh
devices (for example: FM Racer
interface)
Packet implicitly tagged with MVID, next
rules apply
Signalling traffic Packet implicitly tagged with MVID, next
rules apply
Tagged with valid VID (1 – 4095), not
NVID
Packet passed (tagged)
Tagged with null VID (0) or NVID Packet passed (untagged)
Access port rules for incoming packets with unit in Bridge Mode (Case and
Action)
The Native VLAN enable setting is used to control whether the Management VLAN
should be tagged or not.
Untagged packet, to remote devices Pass packet to remote peer
Tagged packet (any VID), to remote
devices
Pass packet to remote peer with original
tag
Untagged packet, to local unit kernel If native VLAN = ON: Packet passed to
kernel, tagged with NVID
If native VLAN = OFF: Packet not
passed to kernel
Cisco Ultra-Reliable Wireless
Backhaul FM4200 Mobi
© 2020 Cisco and/or its affiliates. All rights reserved. Page 119 of 177