Installation Instructions
Table Of Contents
- Fluidmesh 1200 VOLO
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.1.1. Installing the Fluidmesh 1200 VOLO
- 5.1.2. Best practice for shielded CAT5/6 connectors
- 5.1.3. Fluidmesh 1200 VOLO Status and link LEDs
- 5.1.4. Supplying power to the Fluidmesh 1200 VOLO
- 5.1.5. Rebooting the firmware and resetting the unit to factory defaults
- 5.1.6. Suitability for outdoor installation
- 5.2. Connecting the Fluidmesh 1200 VOLO to networking and communications hardware
- 5.1. Fluidmesh hardware installation
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Fluidmesh 1200 VOLO for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Static routes
- 7.6.4. Pass lists and Block lists
- 7.6.5. Multicast
- 7.6.6. SNMP configuration
- 7.6.7. Wireless access point configuration
- 7.6.8. RADIUS configuration
- 7.6.9. NTP Configuration
- 7.6.10. L2TP configuration
- 7.6.11. VLAN settings
- 7.6.12. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the RACER interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in RACER
- 9.6. I cannot connect my Fluidmesh device to the RACER interface
- 9.7. I applied configuration settings to the device using RACER, but I have lost connection to the device in RACER.
- 9.8. How do I connect an existing pre-RACER device to RACER?
- 10. Device specifications
- 11. PoE injector specifications
- 12. Electrical power requirements
- 13. Heat radiation data
- 14. Federal Communications Commission (FCC) radio interference statement
- 15. Fluidmesh end-user license agreement
- 15.1. Preamble
- 15.2. Notice
- 15.3. Definitions
- 15.4. License grant
- 15.5. Uses and restrictions on use
- 15.6. Open-source software
- 15.7. Termination
- 15.8. Feedback
- 15.9. Consent to use of data
- 15.10. Warranty disclaimer
- 15.11. Limitation of liability
- 15.12. Exclusion of liability for emergency services
- 15.13. Export control
- 15.14. General
- 16. Contact us
IMPORTANT
Due to rising levels of cyber crime, most
modern web browsers are built to alert you to
possible threats, such as hacking, spoofing
and identity theft.
Because the Fluidmesh 1200 VOLO is
connected to the computer using an
unsecured connection (in this case, a CAT5/6
cable), the web browser may show you
security warnings like the one above.
This is normal and expected. During the
configuration process, it is safe to ignore
these warnings.
1. Click the ADVANCED link.
• You will see the following window:
Figure 14. Security certificate warning
(Google Chrome)
2. Click Proceed to [the URL] (unsafe).
• The device login window will be shown:
Figure 15. Fluidmesh device login
window
8. The factory-set login details are as follows:
Fluidmesh 1200 VOLO
© 2020 Cisco and/or its affiliates. All rights reserved. Page 48 of 169