Installation Instructions
Table Of Contents
- Fluidmesh 1200 VOLO
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.1.1. Installing the Fluidmesh 1200 VOLO
- 5.1.2. Best practice for shielded CAT5/6 connectors
- 5.1.3. Fluidmesh 1200 VOLO Status and link LEDs
- 5.1.4. Supplying power to the Fluidmesh 1200 VOLO
- 5.1.5. Rebooting the firmware and resetting the unit to factory defaults
- 5.1.6. Suitability for outdoor installation
- 5.2. Connecting the Fluidmesh 1200 VOLO to networking and communications hardware
- 5.1. Fluidmesh hardware installation
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Fluidmesh 1200 VOLO for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Static routes
- 7.6.4. Pass lists and Block lists
- 7.6.5. Multicast
- 7.6.6. SNMP configuration
- 7.6.7. Wireless access point configuration
- 7.6.8. RADIUS configuration
- 7.6.9. NTP Configuration
- 7.6.10. L2TP configuration
- 7.6.11. VLAN settings
- 7.6.12. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the RACER interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in RACER
- 9.6. I cannot connect my Fluidmesh device to the RACER interface
- 9.7. I applied configuration settings to the device using RACER, but I have lost connection to the device in RACER.
- 9.8. How do I connect an existing pre-RACER device to RACER?
- 10. Device specifications
- 11. PoE injector specifications
- 12. Electrical power requirements
- 13. Heat radiation data
- 14. Federal Communications Commission (FCC) radio interference statement
- 15. Fluidmesh end-user license agreement
- 15.1. Preamble
- 15.2. Notice
- 15.3. Definitions
- 15.4. License grant
- 15.5. Uses and restrictions on use
- 15.6. Open-source software
- 15.7. Termination
- 15.8. Feedback
- 15.9. Consent to use of data
- 15.10. Warranty disclaimer
- 15.11. Limitation of liability
- 15.12. Exclusion of liability for emergency services
- 15.13. Export control
- 15.14. General
- 16. Contact us
5. HARDWARE INSTALLATION
5.1. Fluidmesh hardware installation
5.1.1. Installing the Fluidmesh 1200 VOLO
Environmental rating and unit roles
The Fluidmesh 1200 VOLO (part number FM1200V-HW) is a wireless
radio transceiver unit.
The hardware is contained in an outdoor-rated metal enclosure that can
be easily mounted on poles or walls.
The Fluidmesh 1200 VOLO can operate in any of the following networking
roles:
• As a point-to-point wireless bridge (see “Point-to-point wireless
bridge” (page 16) for details).
• As a single radio unit within a wireless mesh network (see “Mesh
network architecture” (page 17) for details).
• As a principal radio unit or Subordinate radio unit within a point-to-
multipoint wireless network (see 'Using the FluidMAX Management
Setting' in “Advanced radio settings” (page 85) for details).
Installation hardware
Metal clamps are supplied as part of the installation package, to allow
mounting of the unit on utility poles. Refer to the Fluidmesh 1200 VOLO
installation instructions for details.
Antenna staging kit
The Fluidmesh 1200 VOLO installation package includes a staging kit that
allows you to test the vertical alignment of the unit's built-in antenna. The
unit can be mounted on utility poles using plastic cable ties or metal hose
clamps.
Removable bottom housing
The unit features a removable, water-tight bottom housing. The bottom
housing is equipped with an NPT-1 standard-thread cable gland. The
cable gland can house a dual-cable rubber seal that can accept two
shielded Ethernet cables. Three different pre-cut rubber seals are
provided to accept Ethernet cables of different diameter.
Fluidmesh 1200 VOLO
© 2020 Cisco and/or its affiliates. All rights reserved. Page 26 of 169