Installation Instructions
Table Of Contents
- Fluidmesh 1200 VOLO
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.1.1. Installing the Fluidmesh 1200 VOLO
- 5.1.2. Best practice for shielded CAT5/6 connectors
- 5.1.3. Fluidmesh 1200 VOLO Status and link LEDs
- 5.1.4. Supplying power to the Fluidmesh 1200 VOLO
- 5.1.5. Rebooting the firmware and resetting the unit to factory defaults
- 5.1.6. Suitability for outdoor installation
- 5.2. Connecting the Fluidmesh 1200 VOLO to networking and communications hardware
- 5.1. Fluidmesh hardware installation
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Fluidmesh 1200 VOLO for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Static routes
- 7.6.4. Pass lists and Block lists
- 7.6.5. Multicast
- 7.6.6. SNMP configuration
- 7.6.7. Wireless access point configuration
- 7.6.8. RADIUS configuration
- 7.6.9. NTP Configuration
- 7.6.10. L2TP configuration
- 7.6.11. VLAN settings
- 7.6.12. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the RACER interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in RACER
- 9.6. I cannot connect my Fluidmesh device to the RACER interface
- 9.7. I applied configuration settings to the device using RACER, but I have lost connection to the device in RACER.
- 9.8. How do I connect an existing pre-RACER device to RACER?
- 10. Device specifications
- 11. PoE injector specifications
- 12. Electrical power requirements
- 13. Heat radiation data
- 14. Federal Communications Commission (FCC) radio interference statement
- 15. Fluidmesh end-user license agreement
- 15.1. Preamble
- 15.2. Notice
- 15.3. Definitions
- 15.4. License grant
- 15.5. Uses and restrictions on use
- 15.6. Open-source software
- 15.7. Termination
- 15.8. Feedback
- 15.9. Consent to use of data
- 15.10. Warranty disclaimer
- 15.11. Limitation of liability
- 15.12. Exclusion of liability for emergency services
- 15.13. Export control
- 15.14. General
- 16. Contact us
Network addressing
Fluidmesh radio transceivers
Fluidmesh data link layer (layer 2) addressing allows you to configure
each Fluidmesh 1200 VOLO transceiver unit, and each IP device
connected to the unit, according to the IP address class used in the
private LAN to which the Mesh End unit is connected.
Each Fluidmesh radio transceiver unit has a factory-set IP address of
192.168.0.10, and a Netmask of 255.255.255.0.
NOTE
Each individual Fluidmesh radio transceiver unit has a factory-
set 5.a.b.c unit identification number. Each unit is shipped from
the factory with the same IP address, but with a unique unit
identification number.
When a Fluidmesh wireless network is connected to a wired LAN, the
LAN is usually the private control room LAN. Therefore, Fluidmesh radio
transceivers, and all other edge devices that connect the wireless network
to the wired LAN, must be assigned individual LAN IP addresses that are
part of the same subnet. The edge devices will be accessed using those
IP addresses.
A typical network configuration (Fluidmesh Network Addressing) is shown
in “Operating the unit in Mesh Point mode or Mesh End mode” (page 20).
In this configuration, the private LAN IP address class is 192.168.150.0,
with netmask 255.255.255.0. Note that each device has an IP address
belonging to this subnet.
IMPORTANT
IP addresses must not be duplicated within a network. If
addresses are duplicated, IP address conflicts will occur.
Multiple Fluidmesh radio transceiver units can be connected through a
network switch, forming radio clusters. The proprietary routing protocol will
run automatically on the wired part of the network. To activate the cluster
feature, transceiver units that are capable of being set in Mesh Point
mode must be set in that mode.
Connecting and configuring an Ethernet edge device
Ethernet edge devices such as IP cameras and Wi-Fi access points can
be connected to the Ethernet ports of the Fluidmesh 1200 VOLO. Such
edge devices must be configured using the IP subnet scheme defined for
the broadcast domain.
The default IP subnet mask for all Fluidmesh devices is 192.168.0.0 /
255.255.255.0.
Fluidmesh 1200 VOLO
© 2020 Cisco and/or its affiliates. All rights reserved. Page 21 of 169