Installation Instructions
Table Of Contents
- Fluidmesh 1200 VOLO
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.1.1. Installing the Fluidmesh 1200 VOLO
- 5.1.2. Best practice for shielded CAT5/6 connectors
- 5.1.3. Fluidmesh 1200 VOLO Status and link LEDs
- 5.1.4. Supplying power to the Fluidmesh 1200 VOLO
- 5.1.5. Rebooting the firmware and resetting the unit to factory defaults
- 5.1.6. Suitability for outdoor installation
- 5.2. Connecting the Fluidmesh 1200 VOLO to networking and communications hardware
- 5.1. Fluidmesh hardware installation
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Fluidmesh 1200 VOLO for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Static routes
- 7.6.4. Pass lists and Block lists
- 7.6.5. Multicast
- 7.6.6. SNMP configuration
- 7.6.7. Wireless access point configuration
- 7.6.8. RADIUS configuration
- 7.6.9. NTP Configuration
- 7.6.10. L2TP configuration
- 7.6.11. VLAN settings
- 7.6.12. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the RACER interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in RACER
- 9.6. I cannot connect my Fluidmesh device to the RACER interface
- 9.7. I applied configuration settings to the device using RACER, but I have lost connection to the device in RACER.
- 9.8. How do I connect an existing pre-RACER device to RACER?
- 10. Device specifications
- 11. PoE injector specifications
- 12. Electrical power requirements
- 13. Heat radiation data
- 14. Federal Communications Commission (FCC) radio interference statement
- 15. Fluidmesh end-user license agreement
- 15.1. Preamble
- 15.2. Notice
- 15.3. Definitions
- 15.4. License grant
- 15.5. Uses and restrictions on use
- 15.6. Open-source software
- 15.7. Termination
- 15.8. Feedback
- 15.9. Consent to use of data
- 15.10. Warranty disclaimer
- 15.11. Limitation of liability
- 15.12. Exclusion of liability for emergency services
- 15.13. Export control
- 15.14. General
- 16. Contact us
'Fluidmesh Firmware' means the firmware in object code form made
available by Fluidmesh for Fluidmesh Devices; and
'You' and 'Your' mean the company, entity or individual who owns or
otherwise rightfully acquires the Fluidmesh Device into which the
Fluidmesh Firmware will be incorporated.
15.4. License grant
Fluidmesh grants you a non-exclusive, non-transferable license to use a
copy of the Fluidmesh Firmware and accompanying documentation and
any updates or upgrades thereto provided by Fluidmesh according to the
terms set forth below. You are authorized by this license to use the
Fluidmesh Firmware in object code form only, and solely in conjunction
with applicable and permitted Fluidmesh-branded products and/or
services and in accordance with the applicable documentation. You are
granted a limited and non-exclusive license (without the right to sub-
license) to use the software solely for the Fluidmesh Devices that you own
and control, and solely for use in conjunction with the Fluidmesh
Firmware.
15.5. Uses and restrictions on use
You may:
(a) download and use Fluidmesh Firmware for use in Fluidmesh Devices,
and make copies of the Fluidmesh Firmware as reasonably necessary for
such use, provided that you reproduce, unaltered, all proprietary notices
that exist on or in the copies.
You may not, and shall not permit others to:
(a) use the Fluidmesh Firmware on any devices or products that are not
owned by you or your business organization;
(b) use the Fluidmesh Firmware on any non-Fluidmesh Devices;
(c) copy the Fluidmesh Firmware (except as expressly permitted above),
or copy the accompanying documentation;
(d) modify, translate, reverse engineer, decompile, disassemble or
otherwise attempt (i) to defeat, avoid, bypass, remove, deactivate, or
otherwise circumvent any software protection mechanisms in the
Fluidmesh Firmware, including without limitation any such mechanism
used to restrict or control the functionality of the Fluidmesh Firmware, or
(ii) to derive the source code or the underlying ideas, algorithms, structure
or organization from the Fluidmesh Firmware (except that the foregoing
limitation does not apply to the extent that such activities may not be
prohibited under applicable law); or
(e) distribute, rent, transfer or grant any rights in the Fluidmesh Firmware
or modifications thereof or accompanying documentation in any form to
any person without the prior written consent of Fluidmesh.
Fluidmesh 1200 VOLO
© 2020 Cisco and/or its affiliates. All rights reserved. Page 163 of 169