Installation Instructions
Table Of Contents
- Fluidmesh 1200 VOLO
- Table of Contents
- 1. HAZARDOUS CONDITION WARNINGS
- 2. Reporting mistakes and recommending improvements
- 3. Getting Started
- 4. Installing the radio
- 5. Hardware installation
- 5.1. Fluidmesh hardware installation
- 5.1.1. Installing the Fluidmesh 1200 VOLO
- 5.1.2. Best practice for shielded CAT5/6 connectors
- 5.1.3. Fluidmesh 1200 VOLO Status and link LEDs
- 5.1.4. Supplying power to the Fluidmesh 1200 VOLO
- 5.1.5. Rebooting the firmware and resetting the unit to factory defaults
- 5.1.6. Suitability for outdoor installation
- 5.2. Connecting the Fluidmesh 1200 VOLO to networking and communications hardware
- 5.1. Fluidmesh hardware installation
- 6. Using the Fluidmesh Partner Portal
- 7. Device configuration using the configurator interface
- 7.1. Software and hardware prerequisites
- 7.2. Accessing the Fluidmesh 1200 VOLO for device configuration
- 7.3. Switching between offline and online modes
- 7.4. General settings
- 7.5. Network control
- 7.6. Advanced settings
- 7.6.1. Advanced radio settings
- 7.6.2.
- 7.6.3. Static routes
- 7.6.4. Pass lists and Block lists
- 7.6.5. Multicast
- 7.6.6. SNMP configuration
- 7.6.7. Wireless access point configuration
- 7.6.8. RADIUS configuration
- 7.6.9. NTP Configuration
- 7.6.10. L2TP configuration
- 7.6.11. VLAN settings
- 7.6.12. Miscellaneous settings
- 7.7. Management settings
- 7.7.1. View Mode settings
- 7.7.2. Changing the Administrator username and password
- 7.7.3. Overwriting and upgrading the unit firmware
- 7.7.4. Plug-In management
- 7.7.5. The device status view
- 7.7.6. Saving and restoring the unit settings
- 7.7.7. Resetting the unit to factory defaults
- 7.7.8. Logging out
- 7.7.9. Viewing the end-user license agreement
- 8. Software Plug-Ins
- 9. Troubleshooting
- 9.1. I cannot get the Log-in screen
- 9.2. I cannot log in to the RACER interface
- 9.3. I forgot the Administrator password
- 9.4. The wireless link is poor or non-existent in Bridge mode
- 9.5. I purchased a Fluidmesh device, but it is not shown in RACER
- 9.6. I cannot connect my Fluidmesh device to the RACER interface
- 9.7. I applied configuration settings to the device using RACER, but I have lost connection to the device in RACER.
- 9.8. How do I connect an existing pre-RACER device to RACER?
- 10. Device specifications
- 11. PoE injector specifications
- 12. Electrical power requirements
- 13. Heat radiation data
- 14. Federal Communications Commission (FCC) radio interference statement
- 15. Fluidmesh end-user license agreement
- 15.1. Preamble
- 15.2. Notice
- 15.3. Definitions
- 15.4. License grant
- 15.5. Uses and restrictions on use
- 15.6. Open-source software
- 15.7. Termination
- 15.8. Feedback
- 15.9. Consent to use of data
- 15.10. Warranty disclaimer
- 15.11. Limitation of liability
- 15.12. Exclusion of liability for emergency services
- 15.13. Export control
- 15.14. General
- 16. Contact us
Plug-in Is the plug-
in package
removable
and re-
installable?
Function Part number
Fluidity-
Bandwidth
(Mobile)
Yes Enables Fluidity capability for
mobile Fluidmesh devices.
Allows traffic forwarding up to
and including the amount of
bandwidth specified in the
part number.
FM[model
number]-MOB-
MOB-[bandwidth
limit] (FMx200
models)
FM[model
number]-FLU-
MOB-[bandwidth
limit] (FMx500
models)
Fluidity-
Bandwidth
(Trackside)
Yes Enables Fluidity capability for
static-mount Fluidmesh
devices.
Allows traffic forwarding up to
and including the amount of
bandwidth specified in the
part number.
FM[model
number]-MOB-
TRK-[bandwidth
limit] (FMx200
models)
FM[model
number]-FLU-
TRK-[bandwidth
limit] (FMx500
models)
4.9 GHz band Yes Enables operation in the 4.9
GHz emergency band.
Note that the 4.9 GHz band is
not available in Brazil and
Canada.
FM-49
Licensed
Frequencies
Yes Enables the use of any
operating frequency,
regardless of country
selection.
FM-LF
World
Frequencies
No Unlocks the country drop-
down selector on units sold in
territories where the selector
is locked.
FM-WORLD
AES Yes Enables data exchange
according to the regular
Advanced Encryption
Standard.
FM-AES
Fluidmesh
Access Points
Yes Enables WiFi access-point
capability.
FM-AP
VLAN Yes Enables virtual LAN
capability.
FM-VLAN
Virtual Gigabit Yes Enables Fluidmesh Virtual
Gigabit capability.
FM-VGBE
L2TP Yes Enables layer 2 transfer
protocol capability.
FM-L2TP
Fluidmesh 1200 VOLO
© 2020 Cisco and/or its affiliates. All rights reserved. Page 136 of 169