QUICK Install Guide 400H PerforMAX ® FILL VALVE VIDEO HOW-TO VIDEO VISIT: FLUIDMASTER.COM *See back page for important legal information.
GETTING STARTED STEP 1: PREPARE TANK TOOLS NEEDED PARTS OVERVIEW A: TURN OFF WATER Bowl Water Level Dial Tank Water Level Adjustment Screw Bucket Sponge Towel Scissors Refill Tube TURN (Optional) CLOCKWISE B: DRAIN WATER Flush toilet to drain most of the water from the tank.
STEP 2: REMOVE OLD FILL VALVE A: REMOVE CONNECTOR Remove water supply connector from bottom of fill valve by twisting connector nut to the left (clockwise). Towel (Optional) STEP 3: ADJUST HEIGHT OF NEW FILL VALVE A: TWIST FILL VALVE TO ADJUST HEIGHT Top of fill valve cap should measure roughly 3" above top of overflow pipe when installed. LEFT NOTE: Inspect water supply connector. Replace it if it is worn, or you don’t know how old it is, to prevent flooding and property damage.
STEP 4: INSTALL NEW FILL VALVE A: STEP 5: FINISHING STEPS A: ATTACH WATER SUPPLY CONNECTOR TO FILL VALVE Twist to the right (counterclockwise) ATTACH REFILL CLIP TO OTHER END OF REFILL TUBE RIGHT *Hand-tighten only. DO NOT OVER TIGHTEN. B: INSERT FILL VALVE Position refill tube to face flush valve making sure fill valve parts do not interfere with lever arm. Fill Valve B: (Go to www.Fluidmaster.com/support for leak solutions.
STEP 6: FINE-TUNE TANK WATER LEVEL A: FLUSH THE TOILET TO CHECK THE TANK WATER LEVEL After the water stops filling the tank, the water level should be roughly ½ inch below the top of overflow pipe to ensure a proper flush. STEP 7: FINE-TUNE BOWL WATER LEVEL NOTE: The PerforMAX Fill Valve is pre-set to fill the proper bowl water level in most toilets straight out of the box.
STEP 7: FINE-TUNE BOWL WATER LEVEL D: ADJUST THE BOWL WATER LEVEL IF TOO HIGH: Turn the dial clockwise. STEP 8: FLUSH THE TOILET A: FLUSH THE TOILET If you’re satisfied with the flush, YOU’RE DONE! LESS WATER IF TOO LOW: Turn the dial counter-clockwise. MORE WATER YOU DID IT! We knew you could! E: FLUSH TOILET, CHECK BOWL WATER LEVEL Repeat Steps 7D and 7E until water level in bowl matches the line when the fill valve shuts off.
TROUBLESHOOTING REPLACE FILL VALVE SEAL IF THE FILL VALVE: • DOES NOT TURN ON • WON’T TURN OFF • WON’T REFILL TANK A: B: C: REMOVE CAP AND CHECK FOR DEBRIS A: Turn off water supply. B: Flush toilet. C: With right hand push float up, grip and hold shaft under float. D: With left hand twist cap and lever arm counterclockwise to unlock cap. Let cap hang on float cup. E: Hold empty cup upside down over uncapped valve to prevent splashing. F: Turn water supply on and off a few times.
TROUBLESHOOTING FOR CANISTER FLUSH VALVES The Fluidmaster refill clip is not required for installation. If you’ve already installed the refill clip onto the refill tube, simply pull it or cut it off. FOR MANSFIELD® Push refill tube into refill hole at the top of the flush valve cap. ADDITIONAL QUESTIONS? For installation assistance, contact our technical services department. FOR KOHLER® AQUAPISTON Push refill tube onto yellow nipple on flush valve. EMAIL, CHAT or CALL our toll-free number. www.
GUÍA DE INSTALACIÓN RÁPIDA GUÍA DE INSTALACIÓN RÁPIDA 400H VÁLVULA DE LLENADO PerforMAX® PASO 1: PREPARE EL TANQUE A: B: INSTALE CON CONFIANZA *Consulte la última página para obtener información legal importante. HERRAMIENTA NECESARIA Balde, Esponja, Toalla, Tijeras (opcional) EMPEZANDO: RESUMEN DE PIEZAS Dial del Nivel del Agua de la Taza Tornillo de Ajuste del Nivel del Agua del Tanque C: VIDEO VIDEO DE CÓMO HACERLO PASO 2: REMUEVA LA VÁLVULA DE LLENADO ANTIGUA VISITE: FLUIDMASTER.
GUÍA DE INSTALACIÓN RÁPIDA PASO 5: PASOS PARA TERMINAR A: B: C: SUJETE EL CONECTOR DEL SUMINISTRO DE AGUA A LA VÁLVULA DE LLENADO. Gire a la derecha. *Apriete solo con las manos. NO APRIETE DEMASIADO. ABRA EL AGUA. Revise por fugas. (Visite a www.Fluidmaster.com/support para soluciones de fugas). NIVEL DEL AGUA. Después que el tanque termine de llenar, el nivel del agua debe llenar el tanque aproximadamente 1,27CM más abajo de la parte superior del tubo de desagüe para asegurar una descarga apropiada.
SOLUCIÓN DE PROBLEMAS SI LA VÁLVULA DE LLENADO: (PÁGINA 12) • NO SE PRENDE • NO SE APAGA • NO RELLENA EL TANQUE A: B: C: • Coloque el ensamble de la tapa sobre el cuerpo gris de la válvula alineando el brazo de la tapa y el tornillo de ajuste al lado de la manguera de relleno. REMUEVA LA TAPA Y REVISE POR MUGRE A: Cierre el suministro del agua. B: Descargue el sanitario. C: Con la mano derecha, apriete y sostenga el vástago debajo del flotador, suba el flotador con su mano derecha.
NOTES / NOTAS: ¿PREGUNTAS ADICIONALES? Para asistencia para la instalación, comuníquese con nuestro departamento de servicio técnico. EMAIL, CHAT o LLAME a nuestro número gratuito. www.fluidmaster.
WARNING DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS CONTAINING BLEACH OR CHLORINE. Use of such products will: (1) RESULT IN DAMAGE to tank components and MAY CAUSE FLOODING and PROPERTY DAMAGE and (2) VOID FLUIDMASTER WARRANTY. Fluidmaster Flush ‘n Sparkle Toilet Bowl Cleaning System is recommended for those choosing to use in-tank bowl cleaners and WILL NOT VOID the FLUIDMASTER WARRANTY because it will not damage the components. DO NOT overtighten nuts or tank/bowl may crack.
