Instruction Manual

FAST & FLUID MANAGEMENT
PA
G
E N
O
.
25
o
f
27
CW - V1.2 – 10- 05- 2012 (36609) – rev, B
IIX
TR
O
UBL
E
SHO
O
TING
A - Introduction
Before calling your machine supplier or Service Department, please check whether you can solve the problem
yourself. If you cannot, then call the Service Department for advice. Have the model number and serial number
at hand (these can be found on the sticker attached to service door at the side of the machine).
Attention! MOVING PARTS CAN CAUSE INJURY. Always turn off power
before accessing moving parts.
B - Problem solving
Symptom Cause Action
Co
lo
ran
t
int
e
r
m
i
tt
e
n
t
ly
s
pur
t
s
f
r
o
m
t
h
e
nozzle during discharge
>
A
ir b
ubb
les in
t
h
e
c
o
lo
ran
t
>
Opera
t
e
t
h
e
pu
mp
s
e
v
era
l
t
i
m
e
s
w
i
t
hou
t
opening the valve to drive the air back
into the canister. Then allow the
colorant to sit for several minutes to
allow the bubbles to escape.
A
dro
p
o
f
c
o
lo
ran
t
f
a
l
l
s
f
r
o
m
t
h
e
n
o
zz
le
w
he
n
the valve is opened even when the pump is
not operated
>
A
ir
i
s
t
rappe
d in
t
h
e
c
y
li
nde
r
as
s
e
m
b
ly
>
Opera
t
e
t
h
e
pu
mp
s
e
v
era
l
t
i
m
e
s
w
i
t
hou
t
opening the valve to drive the air back
into the canister. Then allow the
colorant to sit for several minutes to
allow the bubbles to escape.
The
en
d
c
a
p
t
w
i
s
t
s
o
r l
i
f
t
s
dur
ing
o
pera
t
ion
>
E
n
d
-
c
a
p
gru
b
-
s
c
re
w
s
ar
e lo
o
s
e
>
L
i
gh
t
l
y
t
i
gh
t
e
n
t
h
e
2
gr
u
b
-
sc
r
e
w
s
i
n
t
h
e
end-cap (for 53 XB/XD/XE tighten the
end-cap sleeve) until the end cap can no
longer be twisted by hand.
Can
i
st
e
r
i
s lo
o
s
e
o
n
t
ur
n
t
ab
le
>
Loo
s
e
f
i
x
ing
s
c
re
w
s
> Tighten fixing screws with a philipps
head screwdriver
Co
lo
ran
t
appear
s
o
n
t
h
e
p
i
st
o
n
s
h
a
ft
,
p
i
st
o
n
and/or gauges
>
W
o
r
n
s
ea
l
s
>
Rep
la
c
e
s
ea
ls
–
re
f
e
r
t
o
pag
e
s
3
3
t
o 36
Co
lo
ran
t
doe
s
n
o
t
d
i
s
pen
s
e
ea
s
i
ly
>
Nozz
le
b
lo
ck
e
d
>
Re
m
o
v
e
no
zz
le
an
d
c
l
ea
n
i
n
w
a
r
m
soapy water
Co
lo
ran
t
s
t
ill
doe
s
no
t
d
i
s
pe
n
s
e
e
a
s
ily
>
H
igh
v
i
s
c
o
s
i
t
y
o
f
c
o
lo
ran
t
>
I
n
c
rea
s
e
t
h
e
s
i
z
e
o
f
t
h
e
no
zz
l
e
Co
lo
ran
t
ha
s
hardene
d in
t
h
e
c
an
i
st
e
r
an
d
piston assembly
>
>
Can
i
st
e
r
an
d
pu
mp
s
hou
l
d
b
e
re
m
o
v
ed
,
emptied, stripped and cleaned
thoroughly. Replenish only with new
colorant
A
g
i
t
a
t
i
o
n
i
s
no
t
o
cc
urr
i
n
g
>
N
o
p
o
w
e
r
t
o
t
h
e
d
i
s
pen
s
e
r
> Check that the unit is connected and
that there is power to the outlet