Above Ground Poool Filterr & Pump p Manuaal VER.
CONGRATULATIONS! YOU HAVE PURCHASED A HIGH QUALITY FlowXtreme FILTRATIONS SYSTEM FOR YOUR ABOVE GROUND POOL. YOUR NEW FILTER SYSTEM HAS BEEN MANUFACTURED AND TESTED TO OFFER MANY YEARS OF TROUBLE FREE SERVICE. IMPORTANT – READ THIS MANUAL CAREFULLY A. Safety Warnings Read all Warnings and Cautions noted below. Failure to do so could result in serious or fatal injury.
B. General Information This manual provides information relating to the installation, utilization and maintenance of our filtration system. We recommend that you read this manual in its entirety and keep it for future reference, The pump included with the filtration system is a horizontal, self-priming centrifugal pump. For the pump to function correctly, the water temperature must not exceed 35℃/95℉. The materials used in the pump have undergone stringent hydraulic testing and electrical inspections.
Only original replacement parts are used for repairs or replacements (consumable & expendable parts do no fall under the warranty). Expendable parts that do not fall under the warranty include: All O-rings Pressure gauge Mechanical seal, complete Hoses and metal hose clamps F. Resultant Damages We cannot be responsible for damages to the product if the product is not used in accordance with the instructions provided. G.
For the operation of this filter system with Above Ground pools, you need a skimmer installed in your pool. Either an integrated skimmer (built into the pool wall) or a suspended floating skimmer (attachment to the pool wall). The installation area must allow an adequate safety margin to the pool wall. Refer to local and national codes for required distance between the filter system and the pool wall. We recommend putting the filter system on a concrete slab or similar.
designation “RETURN” to the return fitting or connection for the pool location. Secure all connections with hose clamps. (Figures 13 & 18) If using flexible hose: Lightly lubricate the pool return port on the tank cover with petroleum jelly. Secure with a hose clamp. NOTE: Be careful not to secure return hose to the waste/backwash port. e. Backwash: Connect to “WASTE” using backwash hoses and clamps. Backwash hose and clamps are available from your local swimming pool retail professional. f.
8. When you first fill your filter tank with sand it is necessary to clean the small particles and dust from the new sand. If you do not do this you will blow this dust and small particles into your pool. To properly clean the new sand follow the backwash process described below: Turn off the Motor / Pump at the Power Source. Attach backwash hose (not included) to backwash port. Available at a local pool store. Place the Multi-Port Valve in the “4 – Backwash” position.
Closed Position 5 Picture 23 Function: Cleaning the hair and lint strainer. This position stops the flow of water into the pump and filter. CAUTION: Do not run pump with valve in this position. Purge/Drain Position 6 Picture 24 Function: Bypass the filter. This position is ideal for vacuuming pools with large amounts of debris or after an algae treatment. In this position, water bypassed the filter and sends all the water and contaminates out the waste line.
DON’TS: Observe these cautions carefully or you may cause non-warranty damage to your filter system. Move valve handle while the pump is running. It will damage the valve and possibly other equipment as well. Backwash excessively. Sand filters operate more efficiently during mid-cycle. Some level of debris in the sand bed actually helps filtration and makes the filter more effective. Too much backwashing will reduce efficiency. Vacuum the pool in backwash mode.
S.
T. FlowXtrem 16" AG SYSTEM NE4487/4488/4489 PARTS BREAKDOWN AND DIAGRAMS Key Part Name Qty Mnfg. No. B.W. No.
28 Tank Bottom Strainer 1 T00120 NEP4277 NE4487/4488/4489 29 Filter Tank 1025 1 T00121 NEP4278 NE4487 29 Filter Tank 1050 1 T00122 NEP4279 NE4488 29 Filter Tank 1075 1 T00123 NEP4280 NE4489 30 Drain Cap 1 T00124 NEP4281 NE4487/4488/4489 31 Drain Cap Gasket 1 T00125 NEP4282 NE4487/4488/4489 32 Filter Pump Hose 1025 (W/Screw Head) 1 P00127 NEP4242 NE4487 32 Filter Pump Hose 1050 1 P00128 NEP4243 NE4488 32 Filter Pump Hose 1075 1 P00129 NEP4244 NE4489 33 H
12
U. TECHNICAL DATA for FlowXtreme Prime Single Speed Pump Model #s; NE4523, NEP4268, NEP4269, NE4524, NEP4271 Technical Data Model HP Voltage Hertz Amps Flow Rate GPM NE4523 0.75 115 60 5.5 38GPM NEP4268 0.33 115 60 2.5 24GPM NEP4269 0.50 115 60 4.5 35GPM NE4524 1.50 115 60 15.5 115GPM NEP4271 1.0 115 60 11.0 90GPM FlowXtreme PRIME, SPS1 Pumps Parts Breakdown & Diagram Key Part Name Qty Mnfg. No. B.W. No.
FlowXtrem me PRIME E, SPS3 P Pumps Pa arts Break kdown & Diagram m Model M #s;; NEP427 71, NE452 24 Key P Part Name Qtyy Mnfg. No. B.W W. No.
V. Troub bleshootin ng for and d FlowXtrreme Prim me Pump ps Motor Wiill NOT Staart – Check k For: Make sure thhe terminal booard connectio ons agree withh the wiring diiagram on mottor data plate label. Be suree motor is wireed for available field supply voltage v (see pump operatingg label). c breakerrs, GFCI’s, or blown fuses. 1. Improoper or loose wiring connecctions; open sswitches or rellays; tripped circuit Solution: Check all connections, c circuit c breakerrs, and fuses.
automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The “thermal overload protector” will allow the motor to automatically restart once the motor has cooled. It will continue to shut off until the problem is corrected. Be sure to correct cause of overheating. Motor Hums, But Does NOT Start – Check For: 1. Impeller jammed with debris. Solution: Have a qualified repair professional open the pump and remove the debris. 2.
Noisy Pump – Check For: 1. Air leak in suction piping, cavitation caused by restricted or undersized suction line or leak at any joint, low water level in pool, and unrestricted discharge return lines. Solution: Correct suction condition or tighten fittings, if practical. Holding hand over return fitting will sometimes prove this point or putting in a smaller return eyeball fitting. 2. Vibration due to improper mounting, etc.
W. Warranty Information This product is warranted to the original purchaser to be free from defects in material or workmanship for a period of one (1) year from the date of the original retail purchase. This warranty does not cover defects or damage due to improper installation, alteration, accident or any other event beyond the control of the manufacturer. Defects or damage resulting from misuse, abuse or negligence will void this warranty.
La garantie du produit est valide pour l'acheteur original en ce qui a trait aux pièces défectueuses ou à la main-d’œuvre pour une période de 1 année de la date d’achat. Cette garantie n’est couvre pas les dommages causés par accident, par modification, par une installation défectueuse ou tout autre événement hors du contrôle du fabricant. Tout défaut ou dommage résultant de la négligence ou d’une mauvaise utilisation annule cette garantie.