OWNER’S MANUAL INSPIRED BY
TABLE OF CONTENTS Product Information........................................4 Product Diagram..............................................5 Parts........................................................................6 Recommended Tools......................................7 Installation Types..............................................8 Installation..........................................................10 Troubleshooting Guide...............................24 5 Year Warranty........................
PRODUCT INFORMATION PRODUCT DIAGRAM Information produit Diagramme de produit Product Features • • • • • • • • Metal lever handle 2 function spray head Single-hole or 3-hole installation Drip-free ceramic cartridge 1.8 gal/min max at 60 psi Metallic waterway Dual-sensor functions: infrared activated & pull down activated Trouble-free installation with patented mounting hardware and quick-connect Caractéristiques du produit • • • • • • • • Codes/Standards Applicable: Complies with: • ASME A 112.18.
PARTS RECOMMENDED TOOLS (NOT INCLUDED) Les Pièces OUTILS RECOMMANDÉS (Non Inclus) Faucet Robinet Mounting Hardware (silicone washer, rubber washer, metal washer, mounting nut, screws set) Spray Head Tête de pulvérisation Adjustable Wrench Safety Goggles Screwdriver Silicone Sealant Drill 4 AA Batteries Counter Weight MAINTENANCE Contrepoids Entretien Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft cloth.
INSTALLATION TYPES NOTE BEFORE INSTALLING Types d’installation Remarque Avant L’installation SINGLE HOLE INSTALLATION This product includes a safety clip. The safety plug must be removed when switching between motion activated and manual operation. Installer Avec Un Orifice Normal Operating Condition Ce produit comprend un clip de sécurité. La sécurité la prise doit être retirée lors de la commutation entre le mouvement activé et opération manuelle.
INSTALLATION Installation NOTE: Flush water lines before installation to release built up impurities of water supply. REMARQUE: Rincez les conduites d’eau avant l’installation pour libérer les impuretés accumulées dans l’alimentation en eau. Step 1 for 1-hole sink Step 1 for 3-hole sink Insert the O-ring over the hoses, cable, and stem which are located at the bottom of the faucet. Then mount the faucet onto the sink. Insert the deck plate over the cable and hoses in the mounting stem.
INSTALLATION (CONT.) Installation (suite) 250mm(9.8in) 450mm(17 .7in ) Outle t connection Raccor t de sortie Step 3 Step 4 Step 5.1 Step 5.2 The preferred mounting distance between the spray hose and the control box is 9.8” (250mm). The preferred mounting distance from control box to the floor is 17.7” (450mm). Mount the control box under the sink using a philips head screwdriver according to the preferred dimensions. Make sure to leave some room to adjust.
INSTALLATION (CONT.) Installation (suite) Weight location label Étiquette d'emplacement de poids Step 6.1 Step 6.2 Step 7 Étape 7 Connect the data cables and secure them tightly by hand. Tie the data cables together with the outlet hose using a zip tie. Do Not include the pull down hose in the zip tie. Install the counterweight on the pull down hose at the marked position (it should be placed on the line).
INSTALLATION (CONT.) Installation (suite) Step 8 Étape 8 Step 9 Step 10 Remove the battery pack cover and battery pack. Insert 4 AA batteries. Put the battery pack back in the control box ad replace the cover firmly. The batteries should be charged or changed when the sensor flashes a red light three times per second. Retirez le couvercle de la batterie et la batterie. Insérez 4 piles AA. Remettez la batterie dans le boîtier de commande et replacez fermement le couvercle.
INSTALLATION (CONT.) Installation (suite) CAUTION: RISK OF PROPERTY DAMAGE! Do not over tighten connections. This will prevent water leakage. NOTICE: Uses care to avoid cross threading or over tightening the connections. Unless otherwise indicated, use an adjustable wrench to tighten one-quarter turn past hand-tight. • Immediately check for any leaks • Continue to check for leaking throughout the first hour of installation. • If leaking occurs, turn off water supply and discontinue use immediately.
INSTALLATION (CONT.) Installation (suite) Step 12 Étape 12 Step 13 Step 14 Open the faucet handle and wave your hand over the sensor. Set the water temperature to desired setting. The water temperature changes by manipulating the handle. Run the water and it will stop automatically in 3 minutes. Check for leaks. Ouvrez la poignée du robinet et agitez votre main sur le capteur. Réglez la température de l’eau au réglage souhaité. La température de l’eau change en manipulant la poignée.
INSTALLATION (CONT.) Installation (suite) Screen filter Filtre d'écran Step 15.1 Étape 15.1 Step 15.2 Étape 15.2 If the water flow rate is lower than normal, there may be build up on the screen filter. Shut off the water valves, remove the outlet hose from the control box, and unscrew the inlet adapter from the control box. Take out the screen filter and clean it. Reassemble the outlet hose connector, inlet adapter, and screen filter.
TROUBLESHOOTING GUIDE Guide de dépannage Condition Possible Cause Solution Condition Possible Cause Solution Water doesn’t flow from the faucet when activated by infrared sensor and/or hand spray is pulled down. Connections my not be properly made. Use the instruction document to verify all connections were properly made. This will ensure water will flow correctly inside the faucet. Faucet handspray feature needs to reset. Water shut off valves are not open.
TROUBLESHOOTING GUIDE (CONT.) Guide de dépannage (SUITE) Condition Possible Cause Solution Water flow stops while using (which is not stop by auto shutoff after 3 mins), or water suddenly flows without any motion. Batteries have been depleted. Verify the batteries are charged/good and in the correct +/- polarity. Change or reorient batteries. Check if there are any water droplets covering the sensor eye that would interfere with its activation.
TROUBLESHOOTING GUIDE Guide de dépannage État Cause possible Solution État Cause possible Solution L’eau ne coule pas du robinet lorsqu’elle est activée par le capteur infrarouge et / ou le jet manuel est abaissé. Les connexions ne peuvent pas être correctement établies. Utilisez le document d’instructions pour vérifier que toutes les connexions ont été correctement effectuées. Cela garantira que l’eau coulera correctement à l’intérieur du robinet.
TROUBLESHOOTING GUIDE Guide de dépannage État Cause possible Solution Le débit d’eau s’arrête pendant l’utilisation (ce qui ne s’arrête pas par arrêt automatique après 3 minutes), ou l’eau coule soudainement sans aucun mouvement. Les piles sont épuisées. Vérifiez que les batteries sont chargées / bonnes et dans la bonne polarité +/-. Changer ou réorienter les piles. Vérifiez s’il y a des gouttelettes d’eau recouvrant l’œil du capteur qui pourraient interférer avec son activation.
5 YEAR WARRANTY GARANTIE 5 ANS 100% Coverage on all parts and labor for the entire product for all five years from original date of purchase. Our obligations under this warranty are limited to repair or replacement, at our option, of products or parts found to be defective, provided that such products were properly installed and used in accordance with instructions. BBC Innovation LLC reserves the right to make such inspections as may be necessary in order to determine the cause of the defect.
GARANTIE 5 ANS GARANTIE 5 ANS Couverture à 100% sur toutes les pièces et main-d’œuvre pour l’ensemble du produit pendant les cinq années à compter de la date d’achat d’origine. Nos obligations en vertu de cette garantie se limitent à la réparation ou au remplacement, à notre choix, des produits ou des pièces jugés défectueux, à condition que ces produits aient été correctement installés et utilisés conformément aux instructions.
Thank You BBC Innovation LLC 7900 S Route 31 Crystal Lake, IL 60014 T. 847.458.2334 support@biobidet.com biobidet.
